Re: [Chrysler300] '56 Power Steering Hose
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [Chrysler300] '56 Power Steering Hose



Jack and all,

I've had custom hoses made that were the same diameter from one end to the other.  Every time you turn the steering wheel, especially while idling there is a noticeable "rumble and vibration" that occurs.  I think this is why the engineers chose to use the reducer in the hose.

John Lazenby

1955 Chrysler New Yorker Deluxe Town & Country
1955 Imperial Newport
1955 Chrysler C300 Tango Red
1956 Chrysler 300B Cloud White
1957 Chrysler 300C Coupe Raven Black
1960 Chrysler 300F Coupe Alaskan White
1963 Volkswagen Beetle Black
2001 BMW ///M5 (A Modern Super Car)
http://www.bmwmregistry.com/models.php?id=10 

----- Original Message ----- 
From: "Jack Farris" <j2farris@xxxxxxxxxxx>
To: "Rich Barber" <c300@xxxxxxx>
Cc: "'johnl'" <john@xxxxxxxxx>; "'Chrysler 300 Club e-mail'" <chrysler300@xxxxxxxxxxxxxxx>
Sent: Monday, September 04, 2006 4:27 PM
Subject: Re: [Chrysler300] '56 Power Steering Hose


> But wait-- one more solution. It worked for my 66/300. No part number  
> required. I took my old hose to NAPA, looked thru a catalog of  
> hydraulic fittings and found two that closely matched what I had. I  
> gave the counter guy the length of hose I wanted, and he made it up  
> for me while I waited. It fits perfectly. No rubbing on the fender  
> well, or anywhere. Not only that, but it's one diameter hose from  
> gearbox to pump.
> 
> Jack
> ------------------------------------------------------------
> 
> 
> On Sep 4, 2006, at 2:41 PM, Rich Barber wrote:
> 
>> For possible closure on this subject.
>>
>> I purchased a NAPA 7-829 hose for my 1955 C-300 and found the  
>> following:
>>
>> The hose, its several fittings and reducer all looked like top-flight
>> quality, but had a different appearance from any of the three old  
>> hoses I
>> had on hand.
>>
>> It was a little long-maybe 2"-3", but acceptable.
>>
>> The pump-end steel tubing was bent differently.
>>
>> I had to change out the high pressure outlet fitting on the pump to  
>> accept
>> the female tube fitting.  Fortunately, I had purchased a used pump  
>> and it
>> must have been from a '56 as it had the male X female fitting in  
>> the high
>> pressure outlet.  That fitting is rather specialized and appears to be
>> unlikely that it is a common fitting.  Perhaps some of the other  
>> options
>> posted by John L, below, are better fits and have the proper  
>> fittings for a
>> 1955.
>>
>> The new hose did not want to route with the loop forward, as with the
>> original.  It fit better with the loop backward toward the firewall.
>>
>> Detailed reading of the 1955 Service Manual reveals 10W oil is an  
>> acceptable
>> alternative to Type "A" ATF for power steering fluid.  I found this  
>> after I
>> had filled with DexronIII in the circulating fluid and 90W oil in  
>> the upper
>> housing as per overhaul shop recommendations (since they had not  
>> replaced
>> the upper seal).
>>
>> Recommendations:
>>
>> Identify the gender of the high pressure outlet fitting on your power
>> steering pump before starting to shop.
>>
>> Start shopping for a NOS hose, or one that closely simulates original
>> design, before you need one.  They can be counted to blow at the most
>> inopportune time.  One of our members blew a hose in the carpeted  
>> hallway of
>> Harrah's Stateline Casino while driving it to the ballroom!   
>> However, a
>> local car guy happened to blow his while backing his car into a  
>> parking
>> space at a car show in the local NAPA lot.  That was a quick fix as  
>> he had a
>> Ch**vy and NAPA had the proper hose in stock.
>>
>> Consider using 10W oil when you flush and refill the p/s system.
>>
>> I remain curious over Chrysler's design of these hoses.  Why the two
>> different hose diameters and excessive length?  It would appear  
>> that, with
>> proper fittings of the same size, a much shorter length of hose  
>> could have
>> been used while providing a neater appearance.  Speculation:  Cooling?
>> Detune a resonant length of tubing to reduce pulsation and vibration?
>>
>> Happy Labor Day and C-300'ly,
>> Rich Barber
>> Brentwood, CA
>> 1955 C-300
> 
> 
> 
> To send a message to this group, send an email to:
> Chrysler300@xxxxxxxxxxxxxxx
> 
> For list server instructions, go to http://www.chrysler300club.com/yahoolist/inst.htm
> 
> For archives go to http://www.forwardlook.net/300-archive/ 
> Yahoo! Groups Links
> 
> 
> 
> 
> 
> 
> 
> 
> 
> -- 
> No virus found in this incoming message.
> Checked by AVG Free Edition.
> Version: 7.1.405 / Virus Database: 268.11.7/437 - Release Date: 9/4/2006
> 
>

[Non-text portions of this message have been removed]



To send a message to this group, send an email to:
Chrysler300@xxxxxxxxxxxxxxx

For list server instructions, go to http://www.chrysler300club.com/yahoolist/inst.htm

For archives go to http://www.forwardlook.net/300-archive/ 
Yahoo! Groups Links

<*> To visit your group on the web, go to:
    http://groups.yahoo.com/group/Chrysler300/

<*> To unsubscribe from this group, send an email to:
    Chrysler300-unsubscribe@xxxxxxxxxxxxxxx

<*> Your use of Yahoo! Groups is subject to:
    http://docs.yahoo.com/info/terms/
 




Home Back to the Home of the Forward Look Network Archive Sitemap


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.