Re: [Chrysler300] Fw: Tools explained
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [Chrysler300] Fw: Tools explained



Not listed was the "Air Compressor". My  neighbor 
recently had one explode when the high limit 
switch stuck, and the unit continued to fill 
until it finally exploded. The 20 gal. tank was 
flattened, and the pressure gauges were imbedded 
in the back wall (80 ft.) away. Some how the 
wheels of the Oxy tank cart next to the 
compressor were removed without damaging the 
tanks, and there were rust stains from inside the 
tank on the ceiling (24 ft. high). Probably was 
quite a show, fortunately no one was in the shop at the time. Just a thought.

John Holst, Iowa 300K...

At 08:54 AM 7/21/2010, Keith Boonstra wrote:
>
>
>In our shop we find when you hold your part by hand, the drill press can
>also be used as a finger tip warmer - although it heats the part a
>little more slowly than a grinding wheel. And it certainly is a whole
>lot quicker than taking the time to clamp the part down.
>
>A word of caution though would be that if you want to keep from warming
>your finger tips by wearing a glove, you should hold the part with your
>left hand. Then the clockwise rotation of the drill bit, when it
>violently grabs your glove, will wrap your hand around it in its natural
>curvature rather than backwards against your finger joints. This is
>something we have experimented with in our shop.
>
>Keith Boonstra
>
>-
>
>Ross Therrien wrote:
> >
> >
> > I realize this is not on subject but felt it might be of interest to
> > our group.
> > ----- Original Message -----
> > From:
> > To:
> > Sent: Tuesday, July 20, 2010 6:03 PM
> > Subject: Fw: Tools explained
> >
> > ----------------------------------------------------------
> >
> > *TOOLS EXPLAINED
> > *
> > DRILL PRESS: A tall upright machine useful for suddenly snatching flat
> > metal
> > Bar stock out of your hands so that it smacks you in the chest and flings
> > Your beer across the room, denting the freshly-painted project which
> > you had
> > Carefully set in the corner where nothing could get to it.
> >
> > WIRE WHEEL: Cleans paint off bolts and then throws them somewhere
> > under the
> > Workbench with the speed of light. Also removes fingerprints and
> > hard-earned
> > Calluses from fingers in about the time it takes you to say, 'Oh sh --'
> >
> > ELECTRIC HAND DRILL: Normally used for spinning pop rivets in their holes
> > Until you die of old age.
> >
> > SKILL SAW: A portable cutting tool used to make studs too short.
> >
> > PLIERS: Used to round off bolt heads. Sometimes used in the creation of
> > Blood-blisters.
> >
> > BELT SANDER: An electric sanding tool commonly used to convert minor
> > Touch-up jobs into major refinishing jobs.
> >
> > HACKSAW: One of a family of cutting tools built on the Ouija board
> > Principle. It transforms human energy into a crooked, unpredictable
> > motion,
> > And the more you attempt to influence its course, the more dismal your
> > Future becomes.
> >
> > VISE-GRIPS: Generally used after pliers to completely round off bolt
> > heads.
> > If nothing else is available, they can also be used to transfer intense
> > Welding heat to the palm of your hand.
> >
> > OXYACETYLENE TORCH: Used almost entirely for lighting various flammable
> > Objects in your shop on fire. Also handy for igniting the grease
> > inside the
> > Wheel hub out of which you want to remove a bearing race.
> >
> > TABLE SAW: A large stationary power tool commonly used to launch wood
> > Projectiles for testing wall integrity.
> >
> > HYDRAULIC FLOOR JACK: Used for lowering an automobile to the ground after
> > You have installed your new brake shoes, trapping the jack handle firmly
> > Under the bumper.
> >
> > BAND SAW: A large stationary power saw primarily used by most shops to cut
> > Good aluminum sheet into smaller pieces that more easily fit into the
> > trash
> > Can after you cut on the inside of the line instead of the outside edge.
> >
> > TWO-TON ENGINE HOIST: A tool for testing the maximum tensile strength of
> > Everything you forgot to disconnect.
> >
> > PHILLIPS SCREWDRIVER: Normally used to stab the vacuum seals under lids or
> > For opening old-style paper-and-tin oil cans and splashing oil on your
> > Shirt; but can also be used, as the name implies, to strip out Phillips
> > Screw heads.
> >
> > STRAIGHT SCREWDRIVER: A tool for opening paint cans. Sometimes used to
> > Convert common slotted screws into non-removable screws and butchering
> > your
> > Palms.
> >
> > PRY BAR: A tool used to crumple the metal surrounding that clip or bracket
> > You needed to remove in order to replace a 50 cent part.
> >
> > HOSE CUTTER: A tool used to make hoses too short.
> >
> > HAMMER: Originally employed as a weapon of war, the hammer nowadays is
> > used
> > As a kind of divining rod to locate the most expensive parts adjacent the
> > Object we are trying to hit.
> >
> > UTILITY KNIFE: Used to open and slice through the contents of cardboard
> > Cartons delivered to your front door; works particularly well on contents
> > Such as seats, vinyl records, liquids in plastic bottles, collector
> > Magazines, refund checks, and rubber or plastic parts. Especially
> > useful for
> > Slicing work clothes, but only while in use.
> >
> > DANG-IT TOOL: Any handy tool that you grab and throw across the garage
> > while
> > Yelling 'DANG-IT' at the top of your lungs. It is also, most often,
> > the next
> > Tool that you will need.
> >
> > ----------------------------------------------------------
> > Windows Live Messenger. Multitasking at its finest.
> >
> > ----------------------------------------------------------
> > Upgrade to Hotmail Plus and share more photos with bigger attachments.
> > Click here to find out how Click here to find out how
> >
> > [Non-text portions of this message have been removed]
> >
> >
>
>[Non-text portions of this message have been removed]
>
>
>
>No virus found in this incoming message.
>Checked by AVG - www.avg.com
>Version: 8.5.441 / Virus Database: 271.1.1/3018 
>- Release Date: 07/20/10 18:36:00

  ----------


No virus found in this outgoing message.
Checked by AVG - www.avg.com 
Version: 8.5.441 / Virus Database: 271.1.1/3019 - Release Date: 07/21/10 06:36:00


[Non-text portions of this message have been removed]



------------------------------------

To send a message to this group, send an email to:
Chrysler300@xxxxxxxxxxxxxxx


To unsubscribe from this group, send an email to:
    Chrysler300-unsubscribe@xxxxxxxxxxxxxxx


For list server instructions, go to http://www.chrysler300club.com/yahoolist/inst.htm

For archives go to http://www.forwardlook.net/300-archive/Yahoo! Groups Links

<*> To visit your group on the web, go to:
    http://groups.yahoo.com/group/Chrysler300/

<*> Your email settings:
    Individual Email | Traditional

<*> To change settings online go to:
    http://groups.yahoo.com/group/Chrysler300/join
    (Yahoo! ID required)

<*> To change settings via email:
    Chrysler300-digest@xxxxxxxxxxxxxxx 
    Chrysler300-fullfeatured@xxxxxxxxxxxxxxx

<*> To unsubscribe from this group, send an email to:
    Chrysler300-unsubscribe@xxxxxxxxxxxxxxx

<*> Your use of Yahoo! Groups is subject to:
    http://docs.yahoo.com/info/terms/



Home Back to the Home of the Forward Look Network Archive Sitemap


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.