Re: [Chrysler300] Anything "special" about fuel pump for 1957 Chrysler 3
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [Chrysler300] Anything "special" about fuel pump for 1957 Chrysler 300C?



Wayne Graefen's 300C Restoration Handbook lists two correct fuel pumps for 
the 300C: Carter M2503S and M2610S. The latter has a 'notched flange for 
block face clearance'. The 300C uses the same fuel pump as a single 4bbl 
392.

Ron


----- Original Message ----- 
From: "Ray Melton rfmelton@xxxxxxx [Chrysler300]" 
<Chrysler300-noreply@xxxxxxxxxxxxxxx>
To: "chrysler300" <chrysler300@xxxxxxxxxxxxxxx>
Sent: Sunday, October 19, 2014 8:32 PM
Subject: [Chrysler300] Anything "special" about fuel pump for 1957 Chrysler 
300C?


> Hello All --
>
> I have heard some talk but have never seen  a clear declaration (and
> documentation) about the fuel pump for the 300C being somehow "upgraded"
> from the "regular" pump used on the single-carb models. Although it does
> make some sense that pump for the 300C/D would have to satisfy the
> higher flow demands of the dual-carb 392's, is there any clear
> documentation of this, or is it just an urban legend?  If there are any
> differences, what are they?   Different lever pivot point for longer
> stroke for greater volume/cycle = greater flowrate?  Enlarged internal
> passages?  Higher relief pressure?   I have heard of a "notch" in the
> mating circle of the upper/lower parts of the "special" pump and indeed
> have in my possession two pumps with such a notch ground into them.
> However, the notches are clearly done by someone's grinder long after
> original manufacture; they do NOT look at all like they were part of the
> original casting.  Both pumps carry a rebuilder's metal tag, and I
> strongly suspect that the notches were cut that way merely to allow the
> rebuilder to reassemble the halves in the original orientation -- the
> edges of the notches are shinier and sharper than anywhere else on the
> rest of the casting.
>
> Can anyone provide a definitive and documented differentiation,
> including the standard vs. uprated specs?
>
> If there is indeed a difference, where can one obtain the uprated pump?
> I never see such a thing offered anywhere.
>
> Related question:  If it turns out that I have a lowly standard pump on
> my 300C, is there a way to get it upgraded to "300 specs"?  Where can I
> get the parts to rebuild it, or where can I send my puny pump to get it
> rebuilt to upgraded specs?
>
> Another related question:  Even if there is no such thing as an
> "uprated" pump, can anyone suggest where I could get my standard pump
> rebuilt, and at what cost?   Or am I better off just trying to find a
> NOS or recently rebuilt one?
>
> And a final question that I perhaps should have asked near the beginning
> -- even if there IS a special uprated pump available for the 392 hemis,
> do I really NEED one for my non-racing application? I'm guessing that if
> I ever even attempted somewhat prolonged full-throttle application (like
> maybe tempting fate - and the Cokers, not to mention the troopers!)
> during a brief run to maybe 110 - 120 mph, if the fuel flowrate is
> insufficient, all it's going to do is lie down on the top end, right?
>
> Ray Melton
> Las Cruces, NM
>
>
> ------------------------------------
> Posted by: Ray Melton <rfmelton@xxxxxxx>
> ------------------------------------
>
> To send a message to this group, send an email to:
> Chrysler300@xxxxxxxxxxxxxxx
>
> To unsubscribe from this group, send an email to bob@xxxxxxxxxxxxx or
> go to https://groups.yahoo.com/neo/groups/all/manage/edit
>
> For list server instructions, go to 
> http://www.chrysler300club.com/yahoolist/inst.htm
>
> For archives go to 
> http://www.forwardlook.net/300-archive/search.htm#querylang
> ------------------------------------
>
> Yahoo Groups Links
>
>
>



------------------------------------
Posted by: "Ron Waters" <ronbo97@xxxxxxxxxxx>
------------------------------------

To send a message to this group, send an email to:
Chrysler300@xxxxxxxxxxxxxxx

To unsubscribe from this group, send an email to bob@xxxxxxxxxxxxx or
go to https://groups.yahoo.com/neo/groups/all/manage/edit

For list server instructions, go to http://www.chrysler300club.com/yahoolist/inst.htm

For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
------------------------------------

Yahoo Groups Links

<*> To visit your group on the web, go to:
    http://groups.yahoo.com/group/Chrysler300/

<*> Your email settings:
    Individual Email | Traditional

<*> To change settings online go to:
    http://groups.yahoo.com/group/Chrysler300/join
    (Yahoo! ID required)

<*> To change settings via email:
    Chrysler300-digest@xxxxxxxxxxxxxxx 
    Chrysler300-fullfeatured@xxxxxxxxxxxxxxx

<*> To unsubscribe from this group, send an email to:
    Chrysler300-unsubscribe@xxxxxxxxxxxxxxx

<*> Your use of Yahoo Groups is subject to:
    https://info.yahoo.com/legal/us/yahoo/utos/terms/



Home Back to the Home of the Forward Look Network Archive Sitemap


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.