Re: [Chrysler300] 300 G Fast Idle
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [Chrysler300] 300 G Fast Idle





You can take a large plastic funnel and trim the small end to mate to the Uni-Syn and the large end to mate to your carb top.

John Lazenby



From: "Anna F Noia sa-noia@xxxxxxxxxxx [Chrysler300]" <Chrysler300-noreply@xxxxxxxxxxxxxxx>
To: Ray Jones <1970hurst@xxxxxxxxx>; Val Jeffers <edward1108@xxxxxxxxx>
Cc: John Grady <jkg@xxxxxxxxxxxxxxxxx>; "mgoodknight@xxxxxxxx" <mgoodknight@xxxxxxxx>; "chrysler300@xxxxxxxxxxxxxxx" <chrysler300@xxxxxxxxxxxxxxx>
Sent: Wednesday, August 17, 2016 7:36 AM
Subject: Re: [Chrysler300] 300 G Fast Idle

 
Ray, Val & All
I also have limited experience with the "Uni-Syn" but not with 4BBL carb's. I used it with side draft carbs. (SU's, Strombergs, etc...) Is there a special one set up for a 4BBL carbs? I would like one for myself. 
Best Regards,
Stephen A. Noia
1-408-210-4736 cell


On Wednesday, August 17, 2016 7:04 AM, "Ray Jones 1970hurst@xxxxxxxxx [Chrysler300]" <Chrysler300-noreply@xxxxxxxxxxxxxxx> wrote:


 
An indispensable tool is "Uni-syn".
This measures the carburetor's  airflow.
Going from side, you can balance one to the other.
Easy to use and quickly allows you to balance, probably a major factor in performance.
I've had one for nearly 60 years. Crap, how did that happen?
Ray

John Lazenby sells them to Club members @ a discount.

On Wed, Aug 17, 2016 at 8:15 AM, Val Jeffers edward1108@xxxxxxxxx [Chrysler300] <Chrysler300-noreply@xxxxxxxxxxxxxxx> wrote:
 
Just a thought, would it not be very beneficial to have a video on the club page showing the proper procedure for adjusting the ram carburetors and fast idle ?

                                                                Thanks,

                                                                 Val J


On Tuesday, August 16, 2016 8:19 PM, "'John Grady' jkg@xxxxxxxxxxxxxxxxx [Chrysler300]" <mailto:Chrysler300-noreply@xxxxxxxxxxxxxxx> wrote:


 
Agree; others will get into this. Ram warm up is dicey as one side always pulls off before the other, but sounds like your high idle stop screws are set to high.( simple first thing)  Be sure heat riser valves are working. Remember there is no conventional throttle stop / regular idle, only the air valves ----and throttles must close 100% when off high idle. There are instructions in 60 300F manual supplement —have to have that to do this. Many factors play into it. I’ll let someone else fill a phone book about ram idle. I believe there is  no high idle rpm spec . Somewhat dependent on local climate whether you even need a lot of that working , but heat riser valves must be working no matter what else.
 
Follow instructions exactly , step by step.
From: Chrysler300@xxxxxxxxxxxxxxx [mailto:mailto:Chrysler300@xxxxxxxxxxxxxxx] On Behalf Of 'mgoodknight@xxxxxxxx' mgoodknight@xxxxxxxx [Chrysler300]
Sent: Tuesday, August 16, 2016 7:29 PM
To: edward1108@xxxxxxxxx
Cc: chrysler300@xxxxxxxxxxxxxxx
Subject: Re: [Chrysler300] 300 G Fast Idle
 
 
Sounds like you have a problem with the choke pull-off system.  I don't have specs for your fast idle speed, but without regard to the actual setting it should come back to a slightly fast idle immediately after the engine starts (of course also after you press the gas pedal a little to unload the fast idle cam).  If your pull-off is a vacuum diaphragm you should suspect that it has ruptured.  If it is a piston in the choke's hot air/bi-metal spring chamber you should suspect the vacuum passage to be clogged.
You should not have to wait for operating temperature before you can have a reasonable idle speed.  When working properly there is a step-wise decline in idle speed as the engine warms up, but you should never have to deal with such a high idle speed for an extended time------good way to break a band in the transmission.
 
Marshall Goodknight     


---------- Original Message ----------
From: "Val Jeffers edward1108@xxxxxxxxx [Chrysler300]" <mailto:Chrysler300-noreply@xxxxxxxxxxxxxxx>
To: "chrysler300@xxxxxxxxxxxxxxx" <chrysler300@xxxxxxxxxxxxxxx>
Subject: [Chrysler300] 300 G Fast Idle
Date: Tue, 16 Aug 2016 23:00:42 +0000 (UTC)
 
 What is the correct fast idle RPM ? Mine starts out at around 2,000 and doesn't come off until the temperature gauge reaches normal. Not sure how to adjust. Appreciate any help.
 
 
                                                                                           Thanks,
 
                                                                                           Val J
 
 
 





--
Ray Jones. Y'all come on down an see us. Ya hear?






__._,_.___

Posted by: John Lazenby <french_fryguy@xxxxxxxxx>


To send a message to this group, send an email to:
Chrysler300@xxxxxxxxxxxxxxx

To unsubscribe from this group, send an email to bob@xxxxxxxxxxxxx or
go to https://groups.yahoo.com/neo/groups/all/manage/edit

For list server instructions, go to http://www.chrysler300club.com/yahoolist/inst.htm

For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang




Visit Your Group
Yahoo! Groups
PrivacyUnsubscribeTerms of Use

__,_._,___


Home Back to the Home of the Forward Look Network Archive Sitemap


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.