RE: [Chrysler300] Re: 440 Engines and Cross Rams
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

RE: [Chrysler300] Re: 440 Engines and Cross Rams



Looks like lots of them on E-bay also.

Which model does one need to be looking into??

 

From: Chrysler300@xxxxxxxxxxxxxxx [mailto:Chrysler300@xxxxxxxxxxxxxxx] On Behalf Of Ray Jones 1970hurst@xxxxxxxxx [Chrysler300]
Sent: Friday, November 10, 2017 3:32 PM
To: John Grady; Ray Jones
Cc: timothytomlinson; Larry Jett; Chrysler 300 List
Subject: Re: [Chrysler300] Re: 440 Engines and Cross Rams

 






The one thing I haven't seen in this thread is use of a "Uni-syn" tool.

These are used to balance the air flow of the two carbs.

Measures the venturii flow of a carb, then you mount it on the other carb and see how close it is.

Adjust one against the other until they both match. 

Now ALL cylinders will have the same air for each charge.

No matter if they are on Rams or 2X4 inline manifold.

This will solve 90% of idle and running problems. Simple tool.

I've had one for ... Damn, 50 years.... Even used it on Tri-power Marine engines.

Available from John Lazenby  1 (800) 421-2011 or www.royze.com

 

Ray

 

On Fri, Nov 10, 2017 at 9:49 AM, John Grady jkg@xxxxxxxxxxxxxxxxx [Chrysler300] <Chrysler300-noreply@xxxxxxxxxxxxxxx> wrote:

  

This most likely was due to inability of most “mechanics” to set and tune ram carbs . Many if not most are so far out of whack when you get them the car barely runs . Carb is in trunk etc . A good running 375 hp 440 with properly operating rams , which means correctly assembled carbs, ( see Jamie’s post on that) should be fine ; many of our cars have that . 

Remember —many rams were pulled in early 60’s by dealers as they could not keep owners happy . Why dropped in62 in my opinion , came back with manual choke and real “race car” set up in J for those who “got it”. It is not a Toyota. Deal with it. 

Stock 60-61 ram car bought by wealthy grandma and grandpa and tuned by a flathead mopar dealer guy really caused them grief in early 60’s. that issue of “the golden screwdriver” and lack of understanding still plagues rams . Even basic stuff like idle air is by the air valve , not idle stop baffles some . And warm up from real real cold is dicey at best even when working right .. why the dash pot . And stalling when engaging drive , etc etc . J had special converter fixed a lot of that . J cam only 268 tells you a lot , much less than 392 had even . Or later 440 six pack etc 

Re: no vacuum , air valves vs holding throttle open at idle by screw . Cannot be done “by ear” and the gold screwdriver . 
Jog

Sent from my iPhone


On 9 Nov 2017, at 16:59, timothytomlinson timothytomlinson@xxxxxxxxxxxx [Chrysler300] <Chrysler300-noreply@xxxxxxxxxxxxxxx> wrote:

Folks,

  Years ago I went to Tucson (I was stationed in Ft. Huachuca, AZ) to look at a 300-K Convertible with cross rams.  The fellow had installed a 440 engine from about the 1969/1970 time and put the cross ram induction system on.  He was VERY proud of his handiwork and the price was set accordingly.  The body was solid (an AZ car), interior and top were toast, and the drive train very questionable at best.

  When he finally got the car to start, it barely ran.  He had not heard of having to time the valves differently.  The cam was the normal 440 camshaft and lifters were the hydraulic ones standard for the 440.  

  I do not know the cause of the problems, whether it was the camshaft or what.  I can tell you the car had barely any vacuum at a very fast idle (probably near 1500 rpm to stay running) and it idled very roughly and galloped.  Sounded to me much like any hot rodded car with a very aggressive cam.  Anyway, the fellow thought he had all "normal" 440 internals with the cross rams added.  If his efforts were the norm for such an effort, I would be shy.  However, were the cam set up for a cross ram car, I suspect there would be few issues if any.

  My opinion/war story for what it is worth.  As you may guess I did not buy his car.  I felt it was a semi rolling disaster with undetected major issues yet to be found!

Tim Tomlinson

 

On Thursday, November 9, 2017 11:28 AM, "Larry Jett LarryWJett@xxxxxxxxx [Chrysler300]" <Chrysler300-noreply@xxxxxxxxxxxxxxx> wrote:

 

  

My 300F coupe had a 440 block installed in the late 80's by the restorer Joel Cox.  The only downside was when being 'judged' by the Inc Club, I lost a point once for having too few bolts holding the valve covers down, and once for having the "Highland Park Chirp" starter, rather than the direct drive 1960 model.  Can't answer if the 60 Torqueflight will mate to the 440 but Joel had an Imperial Torquer installed from probably a 62 car so the parking brake could be from the 1960.

 

 

Eat, Drink, and be Larry........

 

 

 

 

 

 

 

                                                                     

 

 

 




-- 

Ray Jones. Y'all come on down an see us. Ya hear?










[Non-text portions of this message have been removed]



------------------------------------
Posted by: "David Schwandt" <finsruskw@xxxxxxxxxxxxxxx>
------------------------------------

To send a message to this group, send an email to:
Chrysler300@xxxxxxxxxxxxxxx

To unsubscribe from this group, send an email to bob@xxxxxxxxxxxxx or
go to https://groups.yahoo.com/neo/groups/all/manage/edit

For list server instructions, go to http://www.chrysler300club.com/yahoolist/inst.htm

For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
------------------------------------

Yahoo Groups Links

<*> To visit your group on the web, go to:
    http://groups.yahoo.com/group/Chrysler300/

<*> Your email settings:
    Individual Email | Traditional

<*> To change settings online go to:
    http://groups.yahoo.com/group/Chrysler300/join
    (Yahoo! ID required)

<*> To change settings via email:
    Chrysler300-digest@xxxxxxxxxxxxxxx 
    Chrysler300-fullfeatured@xxxxxxxxxxxxxxx

<*> To unsubscribe from this group, send an email to:
    Chrysler300-unsubscribe@xxxxxxxxxxxxxxx

<*> Your use of Yahoo Groups is subject to:
    https://info.yahoo.com/legal/us/yahoo/utos/terms/



Home Back to the Home of the Forward Look Network Archive Sitemap


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.