RE: {Chrysler 300} 1964 Torqueflite
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

RE: {Chrysler 300} 1964 Torqueflite



Hi Dan,

 

I was thinking more along the line of modifications for longevity rather than increased HP.

 

Things like:

 

1. The recommendation to decrease the input shaft end play to 0.016 - 0.034 inch. (Hemi Anderson)

 

2. Add an Oil Groove to the Rear Output Shaft Support as many stock units display galling.

 

3. Use an 11/32-inch end mill to elongate the slot on both sides of the stator support oil feed hole.

 

4. Use 5 clutches instead of 4.

 

5. Use billet servos in place of the cast units.

 

Of course, new sprag’s and new oil pump gears and the best friction material and plates I can fine.

 

Not looking to make the shifts much more then stock. Perhaps 300K RAM specs on the governor.

 

I used to have a complete write up from George in the 1980’s with a list of good, better, and best upgrades for spirited street driving of a 300 Torqueflite, but I will be darned if I can find it.

 

James

 

From: Dan Plotkin <dplotkin@xxxxxxxxxxxxxxxxxxx>
Sent: Monday, May 22, 2023 07:10
To: James Douglas <jdd@xxxxxxxxxx>
Cc: 'Chrysler 300 Listserver' <chrysler-300-club-international@xxxxxxxxxxxxxxxx>
Subject: RE: {Chrysler 300} 1964 Torqueflite

 

I defer to Don Verity who routinely rebuilds these units. If you intend to use it as a passenger car I wouldn’t modify anything. I have a later model 727 in a 61 Plymouth behind a 440. I chose it for part throttle downshifting ability. It was built using a B&M Hole Shot converter, TCI performance bands, 4.2 ratio band lever and a heavy duty servo spring. These mods help the 727 survive a pretty strong ram inducted 440. The shifts are quick and firm but not unpleasant. Not sure you need any of this in a stock K, but I’ve been happy since 2007 with this.

 

Danny Plotkin

 

 

From: 'James Douglas' via Chrysler 300 Club International [mailto:chrysler-300-club-international@xxxxxxxxxxxxxxxx]
Sent: Sunday, May 21, 2023 3:09 PM
To: Chrysler 300 List Server (chrysler-300-club-international@xxxxxxxxxxxxxxxx) <chrysler-300-club-international@xxxxxxxxxxxxxxxx>
Subject: {Chrysler 300} 1964 Torqueflite

 

My trans will need rebuilding in the 300K.  What modifications have stood the test of time in the last 20 years and what modifications are just a waste of money?

 

I would appreciate folks’ thoughts.

 

James

--
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/CY5PR19MB617199712A334ABC7925368293429%40CY5PR19MB6171.namprd19.prod.outlook.com.

--
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/CY5PR19MB61711742BC9258D13C90FFF193439%40CY5PR19MB6171.namprd19.prod.outlook.com.


Home Back to the Home of the Forward Look Network Archive Sitemap


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.