RE: {Chrysler 300} Silicone dot 5. Brake fluid
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

RE: {Chrysler 300} Silicone dot 5. Brake fluid



So when moisture accumulates in the brake lines of a vehicle with DOT 5, where does it go ?

 

Ron

 

From: chrysler-300-club-international@xxxxxxxxxxxxxxxx On Behalf Of dplotkin
Sent: Friday, October 06, 2023 12:04 PM
To: John Grady <jkg@xxxxxxxxxxxxxxxxx>; Larry Wood <larryjw7@xxxxxxxxx>
Cc: chrysler 300 club <chrysler-300-club-international@xxxxxxxxxxxxxxxx>
Subject: Re: {Chrysler 300} Silicone dot 5. Brake fluid

 

I am with John on this, I don't know anyone who has DOT 5 employed properly, thoroughly bled, and the brake parts are otherwise dimensionally correct for the car with a problem ever. In fact my 61 Savoy built in 2007 has the same DOT 5 fill in it to this day no rust no problems anywhere.

 

If you have a hobby car that sits half the year like most of us do north of Mason Dixon, you should be using Dot 5 as it will never screw up your brake system and you will never have to deal with it again.

 

 

 

Sent from my Verizon, Samsung Galaxy smartphone

 

 

-------- Original message --------

From: John Grady <jkg@xxxxxxxxxxxxxxxxx>

Date: 10/6/23 8:26 AM (GMT-05:00)

To: Larry Wood <larryjw7@xxxxxxxxx>

Subject: Re: {Chrysler 300} Silicone dot 5. Brake fluid

 

Hi .. something strange happened here as rust is only possible with glycol . Just the chemistry . not debating the story , but it was not silicone fluid that caused this .

Some kind of mistake in labeling or whatever as water is immiscable in silicone . It’s not possible . Or lines had incompatible fluid in them . I do not know , I don’t doubt story 

 

The military has it in every single vehicle they own , often stored 25 years . They have to work for sure the day pulled out . I have it in 25 cars zero issues other than very hard to get bled right  

Yes you can use glycol and  drain every 3 years . I did not follow that on mercedes due to  negligence on my part it cost me 3000 in brake replacement parts and service —  ABS etc which is incompatible with silicone fluid .

 

But over all my 300’s , over many years I’d say 85 % had a big rust pit on the bottom of the wheel cylinder due to water carried there by glycol . It is designed to hold  water until saturated , and that water should come out when you drain it regularly .

But people  NEVER did that on 300 , as the 85% shows . It comes out of saturation in a cold day at the bottom of the wheel cylinder 

What  happens is it was ok anyway  at a long ago rebuild — when you rebuild brake shoes ( depends on wear ) you push pistons in more it seals ok , but as pistons move out with wear of shoe or worst of all a panic stop , one day you uncover the rust pit at the seal lip and all your brake fluid gushes out . It is at 1000 psi 

Some of us think they know more than the military , while i think that may be true in many areas , it is not true here 

I think the only reason it is not standard fare is very high relative cost especially way back then . And difficult bleeding . 

Your mileage may vary , but your glycol will always absorb moisture at master and carry it to wheel cylinders over many years .

Rust pit shows you that , you have all seen it …. 

jg 

 

Sent from my iPhone



On Oct 6, 2023, at 12:14 AM, Larry Wood <larryjw7@xxxxxxxxx> wrote:



I say Ron is right.

I tried dot 5 in my 67 GTX.     With all new wheel cylinders and master cylinder flushed system.       As directed. Refilled with      silicone dot 5. 3 years later i was out for a drive came up on a curve my Brake pedal went to the floor? I took the GTX to the garage and I was dumbfounded.  The wheel cylinder was eat up with rust the fluid was like brown jelly? Was it bad fluid  or what .i have found     no answers yet

.replacing all cylinders and using Dot 4  flush system every 2 years

--
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/CAODNPj9vthZaj4QH%3DOWTx%2BzigfwkMouw5ZZTt6JS_WSAKmy9Mw%40mail.gmail.com.

--
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/7D9891DF-7D13-42D6-B76F-576B1ED6CE9A%40gradyresearch.com.

--
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/65203011.050a0220.752e7.9f5aSMTPIN_ADDED_MISSING%40gmr-mx.google.com.

--
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/000701d9f87d%2473b2d300%245b187900%24%40comcast.net.


Home Back to the Home of the Forward Look Network Archive Sitemap


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.