Re: {Chrysler 300} RE: New Springs Leaf 1963 1964
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: {Chrysler 300} RE: New Springs Leaf 1963 1964



Hi James,
 
I have a '64K convertible equipped with ram induction, I purchased it from Don Cole, who replaced the springs. I count 6 leaves on the springs, and it stands at 27.5" to the lip of the stainless trim at the high point of the wheel well curve. This is with 15" rims and 235/70/15 tires.  I recall Don told me that when he had the springs replaced, he placed some heavy tools or something like that in the trunk, so that when the shop dialed in the height it would stand a bit taller when unloaded.   I don't have a picture handy, but I suspect you can find pictures of this car in the archives.
 
--Mike
On 12/14/2023 11:07 AM EST 'James Douglas' via Chrysler 300 Club International <chrysler-300-club-international@xxxxxxxxxxxxxxxx> wrote:
 
 

Anyone have the time to take a tape measure and tell me the rear wheel well distance from the ground to the underside of the rear wheel well, to determine rear stance, and which springs you are using (6 or 7 leaf) ?

 

I would really like to get my order in and I want to see what the differences are if any between the cars? A side view photo showing how is stands would help in addition to the measurement.

 

Thanks someone…

 

James

 

From: 'James Douglas' via Chrysler 300 Club International <chrysler-300-club-international@xxxxxxxxxxxxxxxx>
Sent: Monday, December 11, 2023 13:19
To: Chrysler 300 List Server (chrysler-300-club-international@xxxxxxxxxxxxxxxx) <chrysler-300-club-international@xxxxxxxxxxxxxxxx>
Subject: {Chrysler 300} New Springs Leaf

 

Hi All,

 

I talked with Mike (Eaton) about springs for the 300K. I mentioned that I liked the 7 leaf 300K RAM (I assume 300J also) springs better than the 6 leaf. My folks 300K had the six and I had switched it to the 7 leaf a couple of years before I sold it (Yes, I am an idiot).

 

We did a trip from San Francisco to Texas in 1964 and two trips down into Mexico in 1968 and 1969. When loaded with full baggage and a kid in the back seat the car hanged down very low in the rear. I remember on dirt roads in Mexico the tailpipe bottoming out in places.

 

The seven leaf 300K RAM spring specifications are:

 

Rate 125 (as is the front torsion bars) and the load is 800.

 

Mike has a set (part number ML9083) that is a seven leaf with a 135-pound spring rate and a 1000-pound load rating, it is also 1.5 inch higher.

 

Mikes take is that the rearends on these early 1960’s Chryslers were under-sprung.

 

Has anyone used the ML9083 spring? I would appreciate thoughts on this. For road trips we would be hauling a lot in the trunk, and we may have a couple of electric bicycles hanging off the back (hitch to be designed and implemented and that will add weight).

 

Also, can a couple of people with a 300J and 300K not RAM and 300K with RAM do me a favor? Can you measure the center of the rear wheel opening arch to the ground so I can get a baseline on rear ride height.  I want to take that measurement and jack up the body 1.5 inch more and see how it will look.

 

Thanks, James

 

PS. Why am I changing 93K miles springs? Some idiot placed a “helper leaf” between the main leaf and the next one in the stack. The ends were cut crude with a torch, and it has no taper or anything else. Also, on the drive side it spit out a little to the right and was hitting the front housing as they also made it too long. I could see an unnatural slight bend in front couple of inches of the main leaf do to the point pressure of the helper spring. Of course all this because the stock 6 leaf if loaded has the ass on the ground, Mike is correct I think on this.

 

--
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/CY5PR19MB6171749D405AE883C15C8342938FA%40CY5PR19MB6171.namprd19.prod.outlook.com.

 

--
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/CY5PR19MB6171C35842CAF251147F0B9E938CA%40CY5PR19MB6171.namprd19.prod.outlook.com.

--
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/829354506.1092763.1702591077511%40connect.xfinity.com.


Home Back to the Home of the Forward Look Network Archive Sitemap


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.