RE: Trans pushbutton units

[Paul Lennemann <pjlenn@xxxxxxxxx>]

I took a look at your pictures and then at my push button unit and there 
really isn't any more to see than with the pictues you've posted.  I 
have both of my cables removed, the park cable by opening up the clamp, 
the shift cable by removing the bracket the cable is attached to. 

Paul L.
'63 Sport Fury
440/727
http://www.1962to1965mopar.ornocar.org/ml-lennemann63.html

Robert Lane wrote:
> 
> Hi Paul, thanks for the reply.
> 
> Our unit has also needed more pressure to depress the buttons than I 
> thought 
> it should. I've always dreaded the thought of using 1st, 2nd, & drive on 
> the 
> 1/4 - wondering how well it would cope when it's really needed!
> Apart from the pressure required to change gear, it didn't really play 
> up 
> until we got the engine & box back in the car, after the rebuild (last 
> Sept). That's why I thought it might be more to do with adjustment down 
> at 
> the trans end.
> We haven't managed/attempted to remove the cables yet. When we saw the 
> brackets had been bent over to retain the cables, we thought it was a 
> previous-owner-bodge. One cable has the 'P' clip (like a hood pin, or 
> hairpin) but the other has no clip. The spindle that it sits on has had 
> its 
> end flattened to stop the cable coming off. I'm sure it could be filed 
> tho 
> to remove the cable end. Any idea what should be holding the cable on? 
> Another P clip?
> We should be able to do something with the brackets too, so will attend 
> to 
> that next time.
> These are a couple of pics taken when the unit was hanging from the 
> dash. 
> You can just about see the cable ends & the brackets bent over.
> http://uk.pg.photos.yahoo.com/ph/rob426uk/album?.dir=/b785scd&.src=ph&.tok=phx4.OGBSPWSf43B
> 
> Paul, when you had your unit removed, can you remember if, when you 
> pressed 
> the pushbutton levers, did they stay latched in when pressed? I don't 
> remember any of our levers staying in; they all just sprang back. Just 
> trying to get an idea what to look for to identify whether there is 
> anything 
> wrong with our unit, or whether it's more cable/trans.
> 
> Best Regards
> 
> Robert
> 63 Polara 500
> England
> 
> 
> ----- Original Message ----- 
> From: "Paul Lennemann" <pjlenn@xxxxxxxxx>
> To: <1962to1965mopars@xxxxxxxxxx>
> Sent: Saturday, February 03, 2007 2:40 PM
> Subject: RE: Trans pushbutton units
> 
> 
> >
> > Robert, How did the unit work before the rebuild?  What happens if you
> > disconnect the cable by removing the small retaining clip, "hairpin" and
> > operate the unit free of the cable?  When I bought mine it had similar
> > problems, when you pushed drive the previously depressed button wouldn't
> > always pop out.  I used some penetrating oil and compressed air to
> > remove accumulated lint, dust, etc. and get it lubed up again.  This
> > cured the problem.  Mine still takes more pressure than I think it
> > should to get the buttons depressed but at least beyond that it is
> > working correctly.
> >
> > Paul L.
> > '63 Sport Fury
> > 440/727
> 


----
Please address private mail -- mail of interest to only one person -- directly to that person.  I.e., send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic.  Thanks!

'62 to '65 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html. 



u/?bUrDWg.bSONJP.YXJjLjYy