Re: Tming Chain Stupid Question
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: Tming Chain Stupid Question



OK all I am the dummy, The firing order was correct but one terminal off. Got 
the timing sorta set, car runs much better, no more exhaust popping, the only 
thing I need now to sort out is that the engine wants to keep dying below 2k 
rpm, Fuel pressure is 3 psi at the regulator which I will increase to 5 psi.I 
also may still have a vacuum leak but at least it starts fairly easy and raps 
up nicely. Thanks for all the input, you folks are the greatest.
Nico


On Wed, 21 Apr 2010 09:03:04 EDT, Dodger7998 wrote
> I agree,,,,,,,if the engine is running at all, I think that the 
> gears and  the dist. are in a workable position, double or even 
> triple check the firing  order, it is so easy to make the same 
> mistake twice,,,,,,,,   and on a  second note  Herb,,,,,,  thanks 
> for coming back and clarifying   that I had not lost my mind (well 
> at least totally)
> 
> In a message dated 4/21/2010 5:46:57 A.M. Central Daylight Time,  
> dongallimore@xxxxxxx writes:
> 
> Moving on from the timing gear issue. I don't think we've  solved 
> his problem.
> 
> The stalling sounds like a timing related  problem. I suggest he 
> check the spark plug firing order. Especially 5 and  7.  Car will 
> run with these swapped but  not very  good.
> 
> One common problem is a vacuum leak but the motor usually runs 
>  faster, not stall out, as in Nico's case.
> 
> Akron  Don
> 
> Nico Over wrote:
> > All, just finished putting Eddy Victor  Heads ported to Max wedge size, 
> Indy 
> > dual plane intake, Crane  Hydraulic Roller in the winter top end overhaul 
> of 
> > the 440 in my 63  330. It barely runs, pops out the exhaust on decel, 
> won't 
> > idle. I  have moved the timing all over the place from staright up to 33 
> >  degress at 3k with no difference in running characteristics. I am sure 
> that  
> > all the plugs are firing and the valves are adjusted properly so am  at 
> my 
> > wits end on this one. Now, the only thing I can figure that I  messed up 
> on 
> > the build was that I set the timing marks in line top of  each gear at 
> TDC 
> > firing instead of the bottom of cam gear to top of  crank gear. So my 
> question 
> > is: will setting the timing marks the way  I did manifest itself as I 
> have 
> > noted above. I really don't want to  rip it all back apart but will if i 
> have 
> > to. Any thoughts would be  greatly appreciated.
> > Nico Over
> > Va. Beach,  Va.
> >
> >
> > ----
> > Please address private mail -- mail  of interest to only one person -- 
> directly to that person.  I.e., send  parts/car transactions and 
> negotiations as well as other personal messages  only to the 
> intended recipient, not to the Clubhouse public address. This  
> practice will protect your privacy, reduce the total volume of mail 
> and fine  tune the content signal to Mopar topic.  Thanks!
> >
> > 1962 to  1965 Mopar Clubhouse Discussion Guidelines:
> >  http://www.1962to1965mopar.ornocar.org/mletiq.html and  
> http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.  
> >
> >
> >
> 
> ----
> Please address  private mail -- mail of interest to only one person -
> - directly to that  person.  I.e., send parts/car transactions and 
> negotiations as well as  other personal messages only to the 
> intended recipient, not to the Clubhouse  public address. This 
> practice will protect your privacy, reduce the total  volume of mail 
> and fine tune the content signal to Mopar topic.   Thanks!
> 
> 1962 to 1965 Mopar Clubhouse Discussion  Guidelines:
> http://www.1962to1965mopar.ornocar.org/mletiq.html and  
> http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
> 
> --
> [Non-text portions of this message have been removed]
> 
> ----
> Please address private mail -- mail of interest to only one person --
>  directly to that person.  I.e., send parts/car transactions and 
> negotiations as well as other personal messages only to the intended 
> recipient, not to the Clubhouse public address. This practice will 
> protect your privacy, reduce the total volume of mail and fine tune 
> the content signal to Mopar topic.  Thanks!
> 
> 1962 to 1965 Mopar Clubhouse Discussion Guidelines:
> http://www.1962to1965mopar.ornocar.org/mletiq.html and 
> http://www.1962to1965mopar.ornocar.com/general_disclaimer.html. --^--
> -------------------------------------------------------------- This 
> email was sent to: nover@xxxxxxxx
> 
> u/?bUrDWg.b6WFAa.bm92ZXJA
> 
> 
> 
> 
> 


----
Please address private mail -- mail of interest to only one person -- directly to that person.  I.e., send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic.  Thanks!

1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html. 













Home Back to the Home of the Forward Look Network


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.