Re: re 62 drums
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: re 62 drums




I have heard of the "cut swedge" solution, but you still have to work around the hub --and can't check bearings and seals. ............................MO
{Steve Mick}
http://stevemick1964dodge.shutterfly.com/pictures/5
----- Original Message ----- From: "Butch Edison" <waedison@xxxxxxxxxxx>
To: <1962to1965mopars@xxxxxxxxxx>
Sent: Friday, March 11, 2011 11:26 PM
Subject: RE: re 62 drums



I'd heard/read/dreamed? That you can use a 9/16 hole saw to cut the swedges off the studs and pull the drum, which I'm going to try on a spare I have. Sounds similar. /Butch/Ferndale, WA

-----Original Message-----
From: beth [mailto:dickens@xxxxxxxxxxxxx]
Sent: Friday, March 11, 2011 7:13 PM
To: 1962to1965mopars@xxxxxxxxxx
Subject: re 62 drums



To all You do not have to do it that way. you use a file or die grinder to take down the raised or swedge around each stud. Now thread a nut on flush and drive the stud in about 1/8 inch. not all the way,now remove the drum the same way as you would on later axles. Before reinstalling pull studs back in full,and open stud holes up just a little. I have done this on all Mopars since i started working on them. This is the way i was taught by my dad and always works. Side note for 10 inch breaks use all fifth ave pieces including hardware and cylinders. For 11inch dodge truck from the late 70’s will work again use all pieces.

 Doug B.
[Non-text portions of this message have been removed]


----
Please address private mail -- mail of interest to only one person -- directly to that person. I.e., send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic. Thanks!

1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.


----
Please address private mail -- mail of interest to only one person -- directly to that person. I.e., send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic. Thanks!

1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.


----
Please address private mail -- mail of interest to only one person -- directly to that person.  I.e., send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic.  Thanks!

1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
This email was sent to: arc.6265@xxxxxxxxxxxxxx

u/?bUrDWg.bSONJP.YXJjLjYy



?p=TEXFOOTER








Home Back to the Home of the Forward Look Network


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.