Scott, I will try to address some of your questions
will heads and exhaust manifolds/headers that work in a RB-engine work also
with a B-engine, assuming they fit the car?
The bolt patterns are the same
Obviously, the header has to be designed for the car,
they may or may not fit, when installing the headers on a B engine, they will be sitting approximately 3/8 inch lower than when installed on a RB engine, and on some applications 3/8 of an inch is just not available
and I know *intakes* from the RBs won't
fit. But if a header or exhaust part fits a '65 C-body, shouldn't it
fit my car as well? Shouldn't all valve covers fit as well?
64 and newer B and RB valve covers will fit the heads, they may not be correct with all the wire tie downs, but will fit
Well, other than the intake manifolds, all the external parts are
interchangeable between the B and RB, right? What about the Max Wedge?
That's a slightly different animal, right?
The max wedge heads will fit, but without a intake to match up with the ports it would be wasted money installing them on a B engine
no reason not to go with a thermostatic fan
I can see no reason not to use the synthetic oil if that is your prefference,,
Hope this answers some of your questions,,,,,
Thank you for the intro, Gary!
I've had my car (as stated earlier: '64 300 non-letter that is as far
as I can tell, completely stock, except for the Pertronix ignition)
for about a month, and I still don't know enough about it. I did say
that I had many questions, so here are a few to start...
My latest questions are all over the place, so here they are: will
heads and exhaust manifolds/headers that work in a RB-engine work also
with a B-engine, assuming they fit the car? Obviously, the header has
to be designed for the car, and I know *intakes* from the RBs won't
fit. But if a header or exhaust part fits a '65 C-body, shouldn't it
fit my car as well? Shouldn't all valve covers fit as well? Well,
other than the intake manifolds, all the external parts are
interchangeable between the B and RB, right? What about the Max Wedge?
That's a slightly different animal, right?
Does anyone know where I can find weatherstrip for my car? Steele
Rubber doesn't seem to carry much of anything for my four-door
hardtop. It seems that Kanter doesn't, either. So far, I've had the
best luck looking though Restoration Specialties' catalog, but even
that is limited for C-bodies before '65. (Yes, I know '65 was the
first "official" year for the C-body)
I've got a leak on both sides that would fill the front wheel wells if
I hadn't pulled the plugs from the floor. Door seals, perhaps?
I'd like to change the differential oil, and I'm wondering if it would
be a good or bad idea to replace it with synthetic. I'm a firm
believer in synth motor oil and tranny fluid, but I don't know about
gear oil with 50-year-old gears. I can't imagine synth doing anything
except improving things out back, but I figure I better ask.
Is there any reason I shouldn't go with a thermostatically-controlled
radiator fan? It seems like I could gain a couple HP, or maybe at
least gain a tenth of a MPG. ;)
Will changing the stock air cleaner to an open element do anything
other than possibly make the engine louder? That's not exactly a bad
thing, but it's not worth the money if it's not worth a few HP. The
same question regarding a dual exhaust: without changing the intake
and exhaust, is a dual exhaust going to do anything, other than make
the engine louder?
Has anyone installed rear seat belts in a car? Where are the best
places to drill the holes? Of course I have the mounting hardware...
Does anyone know of a company that sells spark plug wires WITHOUT a
90-degree boot on the plug end, other than wires to fit a Hemi? I
haven't been able to find any, other than the wires you make yourself,
which might not be a bad option. This beast likes to burn the boots on
the wires (the week-old boots on the Pertronix wires are already
burned, as were the old wires), and the heat shield tubing I bought
won't go over the 90-degree bend. I'm sure I'm not the only person
with this problem...
I think that's it for the moment.
Thanks again for any help!
~S~
On Thu, Jun 23, 2011 at 10:10 PM, <62to65mopar@xxxxxxxxxxx> wrote:
> Welcome to the 1962 to 1965 Mopar Mail List Clubhouse to Scott!
>
> Below is Scott's introductory message.
>
> Thanks,
> Gary H.
>
> ====Introductory Message====
>
> I just bought a '64 300, and I want to learn more about it. I have SO MANY questions...
>
> --
> You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
> To post to this group, send email to 1962to1965mopars@xxxxxxxxxxxxxxxx.
> To unsubscribe from this group, send email to 1962to1965mopars+unsubscribe@xxxxxxxxxxxxxxxx.
> For more options, visit this group at http://groups.google.com/group/1962to1965mopars?hl=en.
>
>
--
--
Please address private mail -- mail of interest to only one person -- directly to that person. That is, send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic. Thanks!
1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
--
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
http://groups.google.com/group/1962to1965mopars?hl=en.
Back to the Home of the Forward Look Network