what is timing set to, and how did you set it
In a message dated 1/16/2014 1:19:14 P.M. Central Standard Time,
hmsevans@xxxxxxx writes:
I joined this thread
to seek parts and advice on my 1962 Sport Fury 413 Project.
After reading
the last thread on Tuning
I would like to ask if it would be OK to ask for
some help solving the issues I have on my just completed 1959 Ply Sport Fury
with a 1959 361 that I had built with a new Cam.
If not OK ,I would
appreciate any input via personal email.
The Problem is Bogging
(almost) to a stall when you want more power at 20-40 MPH cruise. It
will Run strong off the line if you nail it, Starts and idles OK.
Just
unsafe to drive in traffic!
The Motor is a 1959 Plymouth 361 , Bored
.060 over , Heads ,Stock Exh. 1.60, Intakes was, 1.96 ,now 2.08 ,
Cam is a
Schneider , closely resembles the 1960 Commando cam.
The cam is set at 109
deg intake CL/111degs ,Exhaust CL with a 110 deg lobe spread
.Intake
duration is 270 deg/Exh dur is 290 deg.
Intake lift is .440/Exh lift
is .460.
Valve springs are 90-100 lbs.
Compression Stock,
10-1
Carb is rebuilt Carter Stock AFB - 2856S
Distributor is Mopar
Performance Elec Ignition
Running 110 Leaded Race Fuel for tests, runs the
same on unleaded pump gas
I have the Mopar 2x4 Carb ( Carter # 2652S
and 2653S ) setup ready to install. But I would like to sort out the Bogging
issue before I switch the Manifolds.
Any Ideas
Mark
Evans
--
--
--
Please address private email -- email of interest
to only one person -- directly to that person. That is, email your parts/car
transactions and negotiations, as well as other personal messages, only to the
intended recipient. Do not just press "reply" and send your email to everyone
using the general '62-'65 Clubhouse public email address. This practice will
protect your privacy, reduce the total volume of mail and fine-tune the
content signal to Mopar topic. Thanks!
1962 to 1965 Mopar
Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html
and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
--
You received this message because you are subscribed to the Google Groups
"The 1962 to 1965 Mopar Mail List Clubhouse" group.
http://groups.google.com/group/1962to1965mopars?hl=en.
---
You received this message because you are subscribed to the Google Groups
"The 1962 to 1965 Mopar Mail List Clubhouse" group.
To unsubscribe from
this group and stop receiving emails from it, send an email to
1962to1965mopars+unsubscribe@xxxxxxxxxxxxxxxx.
For more options, visit https://groups.google.com/groups/opt_out.
--
--
--
Please address private email -- email of interest to only one person -- directly to that person. That is, email your parts/car transactions and negotiations, as well as other personal messages, only to the intended recipient. Do not just press "reply" and send your email to everyone using the general '62-'65 Clubhouse public email address. This practice will protect your privacy, reduce the total volume of mail and fine-tune the content signal to Mopar topic. Thanks!
1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and
http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
--
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
http://groups.google.com/group/1962to1965mopars?hl=en.
---
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
To unsubscribe from this group and stop receiving emails from it, send an email to
1962to1965mopars+unsubscribe@xxxxxxxxxxxxxxxx.
For more options, visit
https://groups.google.com/groups/opt_out.
Back to the Home of the Forward Look Network