Re: Window winders

In a message dated 1/23/2014 1:56:48 P.M. Eastern Standard Time, pallconservices@xxxxxxxxx writes:

My 62 did not have the hex head bolts in the handles like the 63-65 and the handles were pretty much ruined, so I replaced the brackets with ones from a 65 which fit very well and had the hex bolts but then you would have to replace with 63-65 handles which you may not want to do. But that is always another option if all else fails.
david

On Wed, Jan 22, 2014 at 11:11 PM, Colin Wolf <COLINWOLF@xxxxxxxxxxx> wrote:

Folks,

This is a really small problem, but I need to solve it.

I need to remove the window winder handles on my 1962 Phoenix (Dart). I cannot find the sockets head cap screws which hold the handle on. They may be hidden under a small trim disc which one prises off with a knife or screw driver to reveal the socket. The disk may be glued, or it may snap into a groove. I am extremely wary of doing things like this, because i cannot replace damaged trim parts.

Alternatively, the handle may be attached with a circlip. Usually these can be disconnected by inserting a “slim bladed forked tool” behind the handle and snapping the circlip out. I cannot push the door trim in far enough to see if it has this system or what size it could be.

Can anyone tell me which system I would have, and if it the “bladed forked tool” what is the opening dimension. I can make one out of 16 gge plate.

regards.

Colin Wolf

--
--
--
Please address private email -- email of interest to only one person -- directly to that person. That is, email your parts/car transactions and negotiations, as well as other personal messages, only to the intended recipient. Do not just press "reply" and send your email to everyone using the general '62-'65 Clubhouse public email address. This practice will protect your privacy, reduce the total volume of mail and fine-tune the content signal to Mopar topic. Thanks!

1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
--
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
http://groups.google.com/group/1962to1965mopars?hl=en.

---
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
To unsubscribe from this group and stop receiving emails from it, send an email to 1962to1965mopars+unsubscribe@xxxxxxxxxxxxxxxx.
For more options, visit https://groups.google.com/groups/opt_out.

--

David Blosser, Pres.

PallCon Pallets

239-293-4885

--
--
--
Please address private email -- email of interest to only one person -- directly to that person. That is, email your parts/car transactions and negotiations, as well as other personal messages, only to the intended recipient. Do not just press "reply" and send your email to everyone using the general '62-'65 Clubhouse public email address. This practice will protect your privacy, reduce the total volume of mail and fine-tune the content signal to Mopar topic. Thanks!

1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
--
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
http://groups.google.com/group/1962to1965mopars?hl=en.

---
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
To unsubscribe from this group and stop receiving emails from it, send an email to 1962to1965mopars+unsubscribe@xxxxxxxxxxxxxxxxx
For more options, visit https://groups.google.com/groups/opt_out.