Re: Almost back in business
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: Almost back in business



Sorry - hit send too soon. The short of it was that I replaced the new thermostat with another new thermostat and the temp spikes disappeared.

On Dec 14, 2014 9:04 PM, "Robert Faunce" <bobsbelvedere@xxxxxxxxx> wrote:

For what it's worth I replaced the antifreeze and put it a new thermostat.  I then began experiencing erratic  engine temp with a lot of temp spikes.  I thought I had air in the system and

On Dec 14, 2014 8:26 PM, "'Paul L. http://1962to1965mopar.ornocar.org/ml-lennemann63.html' via The 1962 to 1965 Mopar Mail List Clubhouse" <1962to1965mopars@xxxxxxxxxxxxxxxx> wrote:

I took the stat out today.  I had it installed correctly.  I tested both the new stat and the old one to see that they opened correctly.  Both worked like they should.  When comparing the two side by side I noticed that the new stat has a smaller opening.  It was 3/4" as compared to 1", which means it is nearly 50% smaller.  One thing I had done previously trying to work on the cooling issue was to install a higher volume water pump.  So I wonder if the two components together were the problem.  Maybe causing the pump to cavitate.

I installed the old stat and also drilled an 1/8" hole in the flange to make sure I didn't get an air bubble in the system.  Since it was kind of rainy out today I didn't drive the car but I let it idle in the garage for about 30 minutes at 1000 rpm.  The temp did come up a little higher than it used to but not quite as high as yesterday.  At the highest temp the reading on the upper hose just above the stat housing was 195* and the bottom hose where it exits the radiator was 145*.  This is with the 180* stat.  I didn't get any of the percolating etc. that I did yesterday.  

I'm attaching a two pictures of the temp gauge,one showing where it normally ran on a cool day, the other shows how high it got today before I turned it off.  I've reduced the size of the pictures.

 
Paul

On Thursday, December 11, 2014 9:05:38 PM UTC-6, Paul L. http://1962to1965mopar.ornocar.org/ml-lennemann63.html wrote:
I spent the last two days dropping my 440 back into the Sport Fury.  It has been sitting for the last 14 months due to a detonation problem and a broken piston.  The long time lapse was due to a machinist who had it for more than eight months without doing any work on it.  So I finally just went and picked it up.  Rich K. and Dodger recommended a machinist who is a Mopar guy, but he is also busy.  
The top land broke off of one piston and upon inspection discovered that, that had produced a big dent in the cylinder wall, which could result in a crack.  So it was recommended to sleeve that cylinder, which then means the others have to be bored.  As it was explained to me the cylinders adjacent to the sleeved one get distorted in the process so they need to be bored to bring them back to round so all the others need to be bored as well.
But at last it is ready.  As luck would have it the weather is cooperating and it hasn't been too cold in my unheated garage.  So if everything goes to plan I should be able to fire it up tomorrow.  And the weatherman is forecasting temps in the 50's for the next couple days so I might even be able to go for a bit of a cruise.  Wish me luck.

Paul L.

--
--
--
Please address private email -- email of interest to only one person -- directly to that person. That is, email your parts/car transactions and negotiations, as well as other personal messages, only to the intended recipient. Do not just press "reply" and send your email to everyone using the general '62-'65 Clubhouse public email address. This practice will protect your privacy, reduce the total volume of mail and fine-tune the content signal to Mopar topic. Thanks!
 
1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
--
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
http://groups.google.com/group/1962to1965mopars?hl=en.

---
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
To unsubscribe from this group and stop receiving emails from it, send an email to 1962to1965mopars+unsubscribe@xxxxxxxxxxxxxxxx.
For more options, visit https://groups.google.com/d/optout.

--
--
--
Please address private email -- email of interest to only one person -- directly to that person. That is, email your parts/car transactions and negotiations, as well as other personal messages, only to the intended recipient. Do not just press "reply" and send your email to everyone using the general '62-'65 Clubhouse public email address. This practice will protect your privacy, reduce the total volume of mail and fine-tune the content signal to Mopar topic. Thanks!
 
1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
--
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
http://groups.google.com/group/1962to1965mopars?hl=en.

---
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
To unsubscribe from this group and stop receiving emails from it, send an email to 1962to1965mopars+unsubscribe@xxxxxxxxxxxxxxxx.
For more options, visit https://groups.google.com/d/optout.


Home Back to the Home of the Forward Look Network


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.