Re: Poly Intake Gasket End Seals
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: Poly Intake Gasket End Seals



Ultimately the new CP wind tunnel poly manifold, but a Weiand single plane may get put on briefly. The owner of Racer Brown Cams (Jim Dow) wants to do a dyno comparison of the two manifolds on the same motor. He is acquired a big batch of NOS manifolds and is now selling them. Since I was intending to get my motor dynoed, I thought this would be a pretty neat thing to do while I have the opportunity.

Bill M

On Jan 1, 2015 12:29 PM, <furyus63@xxxxxxxxxxx> wrote:
Bill,
What manifold are you installing?
 
Nick T.
 
 


From: "Bill M" y1topbanana73@xxxxxxxxx
Subject: Poly Intake Gasket End Seals

Getting ready to install my new intake on my motor. When I set it on with the main gaskets in place, the gap at the ends between the intake and block is half the thickness of the end seals. The foam version will compress just fine but will squeeze out unless glued down. The cork won't squeeze out but I'm concerned about its ability to compress that much.

Any thoughts about using one vs the other?

Bill M
65 Coronet 500 'vert http://goo.gl/6xUS1
73 Dart Sport, 05 Ram 2500 CTD, 4WD, QC, LB, Laramie
21 Model T Depot Hack, 06 Mazda 3

 

--
--
--
Please address private email -- email of interest to only one person -- directly to that person. That is, email your parts/car transactions and negotiations, as well as other personal messages, only to the intended recipient. Do not just press "reply" and send your email to everyone using the general '62-'65 Clubhouse public email address. This practice will protect your privacy, reduce the total volume of mail and fine-tune the content signal to Mopar topic. Thanks!
 
1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
--
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
http://groups.google.com/group/1962to1965mopars?hl=en.

---
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
To unsubscribe from this group and stop receiving emails from it, send an email to 1962to1965mopars+unsubscribe@xxxxxxxxxxxxxxxx.
For more options, visit https://groups.google.com/d/optout.

--
--
--
Please address private email -- email of interest to only one person -- directly to that person. That is, email your parts/car transactions and negotiations, as well as other personal messages, only to the intended recipient. Do not just press "reply" and send your email to everyone using the general '62-'65 Clubhouse public email address. This practice will protect your privacy, reduce the total volume of mail and fine-tune the content signal to Mopar topic. Thanks!
 
1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
--
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
http://groups.google.com/group/1962to1965mopars?hl=en.

---
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
To unsubscribe from this group and stop receiving emails from it, send an email to 1962to1965mopars+unsubscribe@xxxxxxxxxxxxxxxx.
For more options, visit https://groups.google.com/d/optout.


Home Back to the Home of the Forward Look Network