RE: 1964 4 speed changesy
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

RE: 1964 4 speed changesy



Ok slip joint at the rear. I was missing something. I've seen them before with slip joint in front. What would be the cost or this set up.



Sent from my Verizon Wireless 4G LTE smartphone


-------- Original message --------
From: NICHOLAS TIBERIO <furyus63@xxxxxxxxxxx>
Date: 12/22/2016 10:22 AM (GMT-05:00)
To: 1962to1965mopars@xxxxxxxxxxxxxxxx
Subject: RE: 1964 4 speed changesy

I lost a large photo file awhile back so I'm missing my conversion photos. Here is the DSS convertion page. The slip joint is located at the rear of the shaft. They explained that's where the most movement is in the drive line so placement at the rear reduces the stress on tailshafts. Many driveshafts will show the slip joint forward, but this idea has been changed. Myself as well as others here have had cracked tailshafts over time.


Ricky Hall has this conversion on his wagon and he has posted photos


http://www.driveshaftspecialist.com/Left-Column/Antique-Classics.html


NIck T.




On December 22, 2016 at 9:12 AM John Waskiewicz <jswask@xxxxxxx> wrote:

Nick that looks great but where is the splines  to take up the up and down movement of the rear axle.  You bolt hard to the trans and to the rear universal joint. there is no movement allowed. Am I missing something



Sent from my Verizon Wireless 4G LTE smartphone


-------- Original message --------
From: NICHOLAS TIBERIO <furyus63@xxxxxxxxxxx>
Date: 12/22/2016 8:14 AM (GMT-05:00)
To: 1962to1965mopars@xxxxxxxxxxxxxxxx
Subject: Re: 1964 4 speed changesy

Jeff,


Another option is just change the driveshaft. Driveshaft Specialists do Ball & Trunion conversions for A833 & A727 all the time. They did one for me and several for friends check it out. My conversion is a standard 4" shaft, Spicer Flange/U-joint, Slip Yoke rear with U-joints to remove vibration and movement from tailshafts, rated @ 600 hp.


http://www.driveshaftspecialist.com/default.html


NIck T.




On December 19, 2016 at 10:24 PM Iwasa4dr <j.macgill@xxxxxxxxxxx> wrote:

I would like to change the flange to a slip yoke on my 64 4 speed 833. What do I have to change and do I have to change the output shaft and gears. The reason I ask is the housing.That I have is for an 3 speed overdrive trans. Any suggestions would be greatly appreciated.Thanks Jeff

 

 

ogle.com/d/optout.

--
--
--
Please address private email -- email of interest to only one person -- directly to that person. That is, email your parts/car transactions and negotiations, as well as other personal messages, only to the intended recipient. Do not just press "reply" and send your email to everyone using the general '62-'65 Clubhouse public email address. This practice will protect your privacy, reduce the total volume of mail and fine-tune the content signal to Mopar topic. Thanks!
 
1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
--
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
http://groups.google.com/group/1962to1965mopars?hl=en.

---
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
To unsubscribe from this group and stop receiving emails from it, send an email to 1962to1965mopars+unsubscribe@xxxxxxxxxxxxxxxx.
For more options, visit https://groups.google.com/d/optout.

--
--
--
Please address private email -- email of interest to only one person -- directly to that person. That is, email your parts/car transactions and negotiations, as well as other personal messages, only to the intended recipient. Do not just press "reply" and send your email to everyone using the general '62-'65 Clubhouse public email address. This practice will protect your privacy, reduce the total volume of mail and fine-tune the content signal to Mopar topic. Thanks!
 
1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
--
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
http://groups.google.com/group/1962to1965mopars?hl=en.

---
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
To unsubscribe from this group and stop receiving emails from it, send an email to 1962to1965mopars+unsubscribe@xxxxxxxxxxxxxxxx.
For more options, visit https://groups.google.com/d/optout.


Home Back to the Home of the Forward Look Network


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.