|
|
Elite Veteran
Posts: 873
Location: ALABAMA, HEART OF DIXIE | After some time off, I got remotavated on my 61 Fury project. Found a great, rust free donor car. The entire rear clip should be grafted onto my vert by the end of the week.
(61 ply parts car (Small).jpg)
(20190307_171340 (Small).jpg)
(DSC04144 (Small).JPG)
(20190307_161706 (Small).jpg)
(20190314_155953 (Small).jpg)
(20190314_170931 (Small).jpg)
(Resized_20190314_171016 (Small).jpg)
Attachments ---------------- 61 ply parts car (Small).jpg (166KB - 181 downloads) 20190307_171340 (Small).jpg (170KB - 181 downloads) DSC04144 (Small).JPG (118KB - 186 downloads) 20190307_161706 (Small).jpg (117KB - 177 downloads) 20190314_155953 (Small).jpg (120KB - 189 downloads) 20190314_170931 (Small).jpg (110KB - 187 downloads) Resized_20190314_171016 (Small).jpg (38KB - 199 downloads)
|
|
|
|
Elite Veteran
Posts: 1172
Location: Georgia | Wow! It looks like some big progress going on. Good to see her back on the active project list. I don't recall how bad the body was
originally, it looks like you're using the front clip from the red sedan as well.
Pete |
|
|
|
Elite Veteran
Posts: 873
Location: ALABAMA, HEART OF DIXIE | Busy couple of days. The sparks are flying now. Both rear clips are cut. Lots of measuring and trimming now. Maybe perform the graft Saturday.
(20190320_095128 (Small).jpg)
(imagejpeg_0donor rear cut (Small).jpg)
(imagejpeg_1donor rear cut 2 (Small).jpg)
(imagejpeg_2 (Small).jpg)
(20190321_151945 (Small).jpg)
Attachments ---------------- 20190320_095128 (Small).jpg (123KB - 169 downloads) imagejpeg_0donor rear cut (Small).jpg (179KB - 179 downloads) imagejpeg_1donor rear cut 2 (Small).jpg (123KB - 185 downloads) imagejpeg_2 (Small).jpg (108KB - 176 downloads) 20190321_151945 (Small).jpg (119KB - 176 downloads)
|
|
|
|
Expert
Posts: 3967
Location: DFW, TX | Wow! Gutted like a fish! Take a few measurements
Can't wait to see how it all turns out. |
|
|
|
Expert
Posts: 2633
Location: Minor Hill, TN | Are you going to use the clips that hod the trimming at the bottom of the windshield? |
|
|
|
Elite Veteran
Posts: 873
Location: ALABAMA, HEART OF DIXIE | A little more progress. 90% of the welds will be at the original panel mating flanges with a small butt weld at each side on the quarters. Frame rails are boxed, spot and tripple butt welded.
(DSC04754 (Small).JPG)
(DSC04755 (Small).JPG)
(DSC04756 (Small).JPG)
(DSC04757 (Small).JPG)
(DSC04758 (Small).JPG)
(DSC04759 (Small).JPG)
(DSC04760 (Small).JPG)
(DSC04761 (Small).JPG)
Attachments ---------------- DSC04754 (Small).JPG (100KB - 174 downloads) DSC04755 (Small).JPG (109KB - 183 downloads) DSC04756 (Small).JPG (126KB - 171 downloads) DSC04757 (Small).JPG (140KB - 167 downloads) DSC04758 (Small).JPG (81KB - 168 downloads) DSC04759 (Small).JPG (74KB - 207 downloads) DSC04760 (Small).JPG (90KB - 178 downloads) DSC04761 (Small).JPG (76KB - 179 downloads)
|
|
|
|
Extreme Veteran
Posts: 380
Location: Kennewick Wa | NICE!!! |
|
|
|
Expert 5K+
Posts: 8947
Location: WHEELING,WV.>>>HOME OF WWVA | planning and common sense , real nice -------------------------------------------------------------later |
|
|
|
Elite Veteran
Posts: 873
Location: ALABAMA, HEART OF DIXIE | Ole Virgil is back to roller status. Fitted back together at all the factory panel welds. Fixing to tackle the floor pans now.
(back up on wheels (Small).jpg)
Attachments ---------------- back up on wheels (Small).jpg (126KB - 182 downloads)
|
|
|