The Forward Look Network
The Forward Look Network
Search | Statistics | User Listing Forums | Chat | eBay | Calendars | Albums | Skins | Language
You are logged in as a guest. ( logon | register )

custom exhaust places
Moderators: Administrator

Jump to page : 1
Now viewing page 1 [50 messages per page]
View previous thread :: View next thread
   Forward Look Local Regions -> Pittsburgh RegionMessage format
 
alumcanTandThd
Posted 2010-12-25 3:37 PM (#254528)
Subject: custom exhaust places



Wise Old Village Idiot

Posts: 3591
20001000500252525
Location: Dellslow, West ("By God") Virginia !
Any you guys know of any 'muffler' shops up there, that do mandrel bending?

Thanks.
Top of the page Bottom of the page
DeSotohead
Posted 2010-12-25 3:39 PM (#254529 - in reply to #254528)
Subject: Re: custom exhaust places



Board Moderator

Posts: 3186
20001000100252525
Location: The not-so-great, dirty-white North ( Michigan)
Merry Christmas Rick!

Find a place that builds race cars/roll cages.
Almost all their benders do mandrel bends as these are structurally stiffer than regular bends......
Top of the page Bottom of the page
alumcanTandThd
Posted 2010-12-25 7:15 PM (#254560 - in reply to #254528)
Subject: Re: custom exhaust places



Wise Old Village Idiot

Posts: 3591
20001000500252525
Location: Dellslow, West ("By God") Virginia !
,,,,humbug, to you too, you old fart! LOL

There is Hassey Chassys, and Rocket Chassis here, that build those roundy-round cars. NEITHER one of 'em will even come near a piece of exhaust pipe!

I need to find a muffler shop that has a mandrel bender, that can bend up custom duals and shuch.

Top of the page Bottom of the page
57desoto
Posted 2010-12-26 8:24 AM (#254590 - in reply to #254528)
Subject: Re: custom exhaust places



Expert

Posts: 1488
1000100100100100252525
Location: New Castle PA
Don't know about the mandrel bends (isn't that where the diameter of the pipe stays the same throughout the bend, unlike the more common bends that show a decrease in diameter?). Shaffer's Exhaust in New Castle will custom bend anything, but with the reduced diameter at the bend.
Top of the page Bottom of the page
alumcanTandThd
Posted 2010-12-26 11:21 AM (#254612 - in reply to #254590)
Subject: Re: custom exhaust places



Wise Old Village Idiot

Posts: 3591
20001000500252525
Location: Dellslow, West ("By God") Virginia !
57desoto - 2010-12-25 8:24 PM

Don't know about the mandrel bends (isn't that where the diameter of the pipe stays the same throughout the bend, unlike the more common bends that show a decrease in diameter?). Shaffer's Exhaust in New Castle will custom bend anything, but with the reduced diameter at the bend.



Ding-ding-ding! Yep, you ARE correct there Kemosaba!

However, almost every corner muffler shop has those 'compression or crush' bending machines. Take a 2 1/2" dia pipe, and crush bend a 45, or any degree bend, the inside diameter is 'crushed' to, 2"

Majority of those 'muffler' places don't even know what the mandrel bender even is!

I want to make a custon set of duals on a New Ford Van I'm fixing. Found out, that the old Porter Glasspacks are being remade! Got a pr, and want to make the duals like OM, mandrel bend, stainless.

Wish they has places like Bob's Muffler out in Calif, around here! He even gives a Old Fart's discount on his custom mandrel bend duals! What he charges for a custom set of mandrel bend duals, is what they charge around here for 'compression/crush' bend duals! Jeeze!

I did a google search, and the only listing for a mandrel bend muffler place (Jak's Muffler 894 Henderson Ave) up there, is in Little Washington. Not even sure if he has a mandrel bender. I'll call to make sure tomorrow.

What I was looking for, if there would happen to be a place up there around Pittsburgh that one of you guys actually had some mandrel bend exhaust work done, that I could go to.

There are NO muffler shops in WV that has a mandrel bender. Even down there in the southern part of the state!
Top of the page Bottom of the page
57plybel
Posted 2010-12-26 8:10 PM (#254662 - in reply to #254528)
Subject: Re: custom exhaust places



Extreme Veteran

Posts: 594
500252525
Location: Melbourne, Australia
Canman, a mandrel bender is HARD to find. Used in industry for heat exchangers, ballustrading, food transport etc etc. They can bend to your sample. (I worked for such a place and made the dies). Have not seen an exhaust shop in posession of one of these machines. Usually they buy a series of 45,90,22.5 degree bends and fabricate to suit with car on a hoist. Diameter is not compromised and more adept to custom fitting like our old cars. Stainless and mild steel bends available. TIG (heliarc) welding usually used. Just had some work done last week on my Galaxie using a series of mandrel bends. Once past the steering box, went back to regular 'press' bends.


Colin
Top of the page Bottom of the page
ruchaven
Posted 2015-04-06 9:52 PM (#474574 - in reply to #254528)
Subject: Re: custom exhaust places


Expert

Posts: 1231
100010010025
Location: York County, PA
Miles Muffler in York may be able to help you, I don't know for sure but you can Google them to find out. Dellslow is on Google earth, just east of Morgantown.

Catch ya later
Top of the page Bottom of the page
mstrug
Posted 2015-04-06 10:15 PM (#474575 - in reply to #254528)
Subject: Re: custom exhaust places



Expert 5K+

Posts: 6487
50001000100100100100252525
Location: Newark, Texas (Fort Worth)
Some suggestions"

http://www.summitracing.com/search/part-type/exhaust-pipes-individu...

on sale"

http://www.speedwaymotors.com/Garage-Sale-2-1-2-Inch-Stainless-Stee...



Top of the page Bottom of the page
Jump to page : 1
Now viewing page 1 [50 messages per page]
Jump to forum :
Search this forum
Printer friendly version
E-mail a link to this thread

* * * This site contains affiliate links for which we may be compensated * * *


(Delete all cookies set by this site)