The Forward Look Network
The Forward Look Network
Search | Statistics | User Listing Forums | Chat | eBay | Calendars | Albums | Skins | Language
You are logged in as a guest. ( logon | register )

Hard Starting 315 Hemi -12V neg ground system
Jump to page : 1 2
Now viewing page 2 [50 messages per page]
View previous thread :: View next thread
   Forward Look Technical Discussions -> Electrical, Battery and ChargingMessage format
 
56D500boy
Posted 2018-03-13 8:42 PM (#559843 - in reply to #559832)
Subject: Re: Hard Starting 315 Hemi -12V neg ground system



Expert

Posts: 4010
20002000
Location: Lower Mainland BC
ronbo97 - 2018-03-13 5:34 PM
Did you get the starter rebuilt ? Ron


Stupidly no. Initially I thought that I would have to get car up on ramps to get the starter off and the logistics of doing that in my tiny 1942-era single car garage are impossible. So I did nothing.

However, I had to take the left front wheel off (and drum) to play with the center-plane brake shoes (not enough lube on the web) and while I had the wheel off, I realized that I had good access to the starter bolts. And still I did nothing.

Finally, when installed the new starter cable the other day, I finally put a wrench (5/8") on the two bolts/nuts and tested them (they will come off). So I was *very* close to taking it off. BUT I didn't. Two (lame) reasons:

1. I finally understand the need for the bent "starter" wrench - neither a socket or a straight box end will work on the forward bolt/nut.

Where is Sears when I need them?



2. I rationalized that I should wait until I see if the issue was the old starter cable.

In the meantime, I asked my neighbour if he could score 4 inches of 1/2" diameter adhesive heat shrink from his sources. He said why not use the self-sealing silicone tape? I laughed. Yup. That would work. And I have some in my Audi tool box. "Rescue Tape".





Edited by 56D500boy 2018-03-13 8:45 PM
Top of the page Bottom of the page
56D500boy
Posted 2018-09-24 6:45 PM (#570717 - in reply to #553804)
Subject: RE: Hard Starting 315 Hemi -12V neg ground system



Expert

Posts: 4010
20002000
Location: Lower Mainland BC
56D500boy - 2017-12-06 11:47 AM

Didn't get a chance to pull the starter. I pulled the bulb out of the glove box light and things have been much better. Started the car yesterday after maybe 10 days of not starting and probably 3 weeks since the battery was on the chargner and it started very nicely. (Yay)

I presume that the glove box light was staying on even with the glove box door shut (and me checking that it was off). Some how.

:)


You won't believe it or care but I went to start the car the other day and found the battery to be 100% flat. Not even enough juice to power my electronically converted Town and Country radio on FM. Had to use my Lithium Ion Jumper pack and even then, it was tough sledding. Drained the jumper pack (Yikes!).

Got the car started, did what I needed to do (test the drive shaft Re and Re) and put it back in the garage with the battery charger on.

The next day (or two days later), I went out to check on things and start the car. As I sat in the dark garage, I looked across at the glove box. It wasn't fully closed and the light was on.

At least now I know why the battery was drained (took several days I guess). That bulb is coming out (again) today.



Edited by 56D500boy 2018-09-24 10:34 PM
Top of the page Bottom of the page
Powerflite
Posted 2018-09-24 10:25 PM (#570734 - in reply to #549163)
Subject: Re: Hard Starting 315 Hemi -12V neg ground system



Expert

Posts: 4904
20002000500100100100100
Location: So. California
Thanks for the "Rescue Tape" info. I didn't know that heat shrink tape existed. Good to know. I'll give that a try on part of my harness that was frayed a little bit. It will save me from having to tear everything apart to replace it.

Speaking of starters; what's odd is my '58 Coronet started very easily and consistently for 2 years, but one night at a car show it stopped cold. It wasn't a power issue as it had plenty of power at the starter. It had jammed itself to a position that it didn't want to move from. I had to get a ride home and come back with a jack, a light, and tools to take the starter out and figure out what to do with it. Once I got the bolts loose enough, it fell into place where it is supposed to sit. Apparently, the last person to put the starter in (about 25 years earlier!) had it slightly ****eyed, but not enough to cause a problem most of the time. Once I had the starter in the proper position, I tightened the bolts back up and it has been working well ever since.
Top of the page Bottom of the page
Jump to page : 1 2
Now viewing page 2 [50 messages per page]
Jump to forum :
Search this forum
Printer friendly version
E-mail a link to this thread



(Delete all cookies set by this site)