The Forward Look Network
The Forward Look Network
Search | Statistics | User Listing Forums | Chat | eBay | Calendars | Albums | Skins | Language
You are logged in as a guest. ( logon | register )

56' Belvedere interior
Jump to page : 1
Now viewing page 1 [50 messages per page]
View previous thread :: View next thread
   Forward Look NON-Technical Discussions -> 1955-1961 Forward Look MoPar General DiscussionMessage format
 
Justinsane
Posted 2018-04-30 10:32 PM (#562564)
Subject: 56' Belvedere interior



25
Location: Binghamton NY
I'm finally at the point of giving the interior a makeover. I've been neglecting it for twelve years now, driving around with rags over the crispy foam on the seats. Torn, stained, and fallen headliner, every bulb blown in the dash, water leaking in through the cracked door seals, side windows rattling from deteriorated window channel and whiskers.
My girlfriend got me a headliner and windlace for Christmas from SMS fabrics to get me motivated. The past few months i've been working on it through the weekends, so i figure i'd post some things for you guys as i work on it, so you can get a glimpse of the project, or maybe pick up some ideas or references if you're planning on fixing yours up.
What i've been building is a 1956 Plymouth Belvedere, two door sedan. It's several cars into one. A significant amount of it is from 1955 plymouth savoys and belvederes. I used what i could from the parts cars but limited too because as you know they changed from 6 volt to 12 and changed the rear end and grill between those years. Most the rest was the same.
Top of the page Bottom of the page
Justinsane
Posted 2018-04-30 10:36 PM (#562565 - in reply to #562564)
Subject: RE: 56' Belvedere interior



25
Location: Binghamton NY
Here's the insulation that was behind the headliner when i tore it out.



(20171226_191923.jpg)



Attachments
----------------
Attachments 20171226_191923.jpg (325KB - 9 downloads)
Top of the page Bottom of the page
Justinsane
Posted 2018-04-30 10:45 PM (#562566 - in reply to #562564)
Subject: RE: 56' Belvedere interior



25
Location: Binghamton NY
Here's a view into it with the door panels off.



(20180421_144636.jpg)



Attachments
----------------
Attachments 20180421_144636.jpg (322KB - 9 downloads)
Top of the page Bottom of the page
Justinsane
Posted 2018-04-30 10:47 PM (#562567 - in reply to #562564)
Subject: RE: 56' Belvedere interior



25
Location: Binghamton NY
Sound deadener insulation..



(20180112_005731 (2).jpg)



Attachments
----------------
Attachments 20180112_005731 (2).jpg (382KB - 9 downloads)
Top of the page Bottom of the page
Justinsane
Posted 2018-04-30 10:56 PM (#562568 - in reply to #562564)
Subject: RE: 56' Belvedere interior



25
Location: Binghamton NY
I had to make the flange wider on the windlace using template board to be able to attach it to the interior. I wrapped it with black gorilla tape to hide the color of the cardboard.



(20180331_162157-1 (2).jpg)



Attachments
----------------
Attachments 20180331_162157-1 (2).jpg (80KB - 9 downloads)
Top of the page Bottom of the page
Justinsane
Posted 2018-04-30 10:59 PM (#562569 - in reply to #562564)
Subject: RE: 56' Belvedere interior



25
Location: Binghamton NY
It went on smoothly and tight. Hopefully when the garnish trim and panels go on, it will cover up the flange.



(20180422_145438 (2).jpg)



Attachments
----------------
Attachments 20180422_145438 (2).jpg (322KB - 10 downloads)
Top of the page Bottom of the page
Justinsane
Posted 2018-04-30 11:07 PM (#562573 - in reply to #562564)
Subject: RE: 56' Belvedere interior



25
Location: Binghamton NY
I couldn't find any decent push buttons so i had to sand mine with 1000 grit sandpaper to get the yellow out of the green plastic, then paint 3/4 of each of them black so the light from the new bulb will shine through. I put some color in the letters and sprayed a flash of clear on them.



(20180428_153504-1 (2).jpg)



Attachments
----------------
Attachments 20180428_153504-1 (2).jpg (229KB - 9 downloads)
Top of the page Bottom of the page
Justinsane
Posted 2018-04-30 11:27 PM (#562578 - in reply to #562564)
Subject: RE: 56' Belvedere interior



25
Location: Binghamton NY
The dash was very tedious and time consuming but i an happy how it's turning out. I still have a few more things to put on it like the stainless trim around the glove box and ashtray, and find a spot to put a clock.



(20180428_160144 (2).jpg)



Attachments
----------------
Attachments 20180428_160144 (2).jpg (65KB - 9 downloads)
Top of the page Bottom of the page
Justinsane
Posted 2018-04-30 11:37 PM (#562582 - in reply to #562564)
Subject: RE: 56' Belvedere interior



25
Location: Binghamton NY
It's still got some flaws but i like it. I'm going to keep the steering wheel wore down, i just have to find a full circle horn ring for it.



(20180425_211419 (2).jpg)



Attachments
----------------
Attachments 20180425_211419 (2).jpg (364KB - 9 downloads)
Top of the page Bottom of the page
60 Imp
Posted 2018-05-01 5:09 AM (#562589 - in reply to #562564)
Subject: RE: 56' Belvedere interior


2000500100100100100
Location: North Australia
Looking good Man.

Steve.

Top of the page Bottom of the page
Justinsane
Posted 2018-05-01 5:51 PM (#562630 - in reply to #562564)
Subject: RE: 56' Belvedere interior



25
Location: Binghamton NY
I ordered the window channel and sweepers from Andy Bernbaum auto parts. I got the sweepers with the chrome edge. I was told the Belvederes didn't use the chrome strip type originally, but i got it anyways for something different. I wasn't sure how they were supposed to go on and didn't have any original ones for reference, but i didn't like it just going straight across to meet the window channel, so i took some extra time and figuring to put a bend in them to follow the window opening lines.



(20180501_171209 (2).jpg)



Attachments
----------------
Attachments 20180501_171209 (2).jpg (393KB - 9 downloads)
Top of the page Bottom of the page
Justinsane
Posted 2018-05-01 5:59 PM (#562631 - in reply to #562564)
Subject: RE: 56' Belvedere interior



25
Location: Binghamton NY
So, here's how far i have it this evening. I ordered some tack strips from michaels i'm probably going to rivet on in the nook above the front window, and around the rear side windows to snug the headliner tighter.



(20180430_221858 (2).jpg)



Attachments
----------------
Attachments 20180430_221858 (2).jpg (461KB - 9 downloads)
Top of the page Bottom of the page
DepsilonD
Posted 2018-05-02 12:53 PM (#562679 - in reply to #562564)
Subject: Re: 56' Belvedere interior



Elite Veteran

Posts: 759
5001001002525
Location: Buena Park, CA
Keep up the good work.
Top of the page Bottom of the page
Powerflite
Posted 2018-05-02 2:07 PM (#562687 - in reply to #562564)
Subject: Re: 56' Belvedere interior



Expert

Posts: 4321
20002000100100100
Location: So. California
Nice. What carpet did you use? it looks molded like the newer ones. I much prefer that to the cut & sewn type that you have to futz with at the hump.
Top of the page Bottom of the page
Justinsane
Posted 2018-05-02 11:16 PM (#562714 - in reply to #562564)
Subject: Re: 56' Belvedere interior



25
Location: Binghamton NY
Powerflite, the carpet i used is one i got from a carpet/upholstery place that was going out of business. I put it in there when i first started building this car back in 2006. It's held up really good all these years, but i never put insulation of anything under it so it wore down in areas that have depresses in the steel on the floor pans. I plan on replacing it this summer and insulating under it. My girlfriend found a company called SMS Auto Fabrics. I've been getting the materials from them. I'm 100% certain they have matching materials for your Savoy if you ever need any. They even have the Aztec pattern that was on the seats. It's expensive though. I ordered three yards of it, but will have to change the layout and use more vinyl. Here's a sample sheet if you're interested..
Top of the page Bottom of the page
Justinsane
Posted 2018-05-02 11:18 PM (#562715 - in reply to #562564)
Subject: RE: 56' Belvedere interior



25
Location: Binghamton NY
Here's the sample sheet..



(20180502_233705.jpg)



Attachments
----------------
Attachments 20180502_233705.jpg (395KB - 9 downloads)
Top of the page Bottom of the page
Justinsane
Posted 2018-06-07 10:18 PM (#564772 - in reply to #562564)
Subject: RE: 56' Belvedere interior



25
Location: Binghamton NY
The interior upholstery panels i got were in bad condition but in good enough condition to be restored. The backing board was warped and most of the fasteners were ripped out so i had to make new panels using the old ones as templates. I had to soak the old ones and flatten them back out so i could trace the outline and holes. I used 1/8" masonite or hardboard.They sell it in 4' X 8' sheets at home depot.



(20180528_140736 2.jpg)



Attachments
----------------
Attachments 20180528_140736 2.jpg (351KB - 4 downloads)
Top of the page Bottom of the page
Justinsane
Posted 2018-06-07 10:28 PM (#564773 - in reply to #562564)
Subject: RE: 56' Belvedere interior



25
Location: Binghamton NY
I put in the panel fasteners and pre fit them in the interior before i glued the padding and vinyl on. I like the look of the original aztec pattern and i'm going to use that pattern on the seats close to the original arrangement so i kept these close to how they were originally.



(20180605_215147-1 2.jpg)



Attachments
----------------
Attachments 20180605_215147-1 2.jpg (218KB - 4 downloads)
Top of the page Bottom of the page
Justinsane
Posted 2018-06-07 10:35 PM (#564774 - in reply to #562564)
Subject: RE: 56' Belvedere interior



25
Location: Binghamton NY
After installing the headliner i put a dome light in from one of the 1955 plymouths i use for parts. About 40% of this car is from 1955 savoys and belvederes. The headliner took some time and was tricky in areas, if any of you need information or advise, feel free to message me and i'll let you know what i went through in the process.



(20180607_184120.jpg 2.jpg)



Attachments
----------------
Attachments 20180607_184120.jpg 2.jpg (215KB - 4 downloads)
Top of the page Bottom of the page
Justinsane
Posted 2018-06-07 10:44 PM (#564775 - in reply to #562564)
Subject: RE: 56' Belvedere interior



25
Location: Binghamton NY
The back area is almost complete besides the seat. Those are going to go in last. Next week i'm going to start on the front door window channels, whiskers, seals, then redo the panels. It's starting to look like something again.



(20180528_211306 2.jpg)



Attachments
----------------
Attachments 20180528_211306 2.jpg (315KB - 4 downloads)
Top of the page Bottom of the page
Powerflite
Posted 2018-06-08 2:07 AM (#564782 - in reply to #562564)
Subject: Re: 56' Belvedere interior



Expert

Posts: 4321
20002000100100100
Location: So. California
Nice job, that looks really good. Did you end up taking the windshield rubber out to do the headliner?
Top of the page Bottom of the page
Justinsane
Posted 2018-06-08 4:45 PM (#564831 - in reply to #564782)
Subject: Re: 56' Belvedere interior



25
Location: Binghamton NY
Thanks! I pulled it pretty tight, i like the fitted bowed look. I did not remove the windshield. I don't know why anyone would. I've heard several people saying you got to remove the windshield and back window, but it doesn't make sense to me. Maybe on other cars you've got to, but not a 1956 plymouth belvedere. I did have to remove the side windows to replace the window channel and wiskers though.
Here's a pic of the liner before i put the garnish molding on, above the front window. There are tack strips in that nook that hold the liner as you stretch it onto them. I sprayed it with upholstery glue too so it'll never go anywhere especially with the garnish molding pressing on it.



(20180519_134718 (2).jpg)



Attachments
----------------
Attachments 20180519_134718 (2).jpg (302KB - 5 downloads)
Top of the page Bottom of the page
Justinsane
Posted 2018-06-08 4:47 PM (#564833 - in reply to #562564)
Subject: RE: 56' Belvedere interior



25
Location: Binghamton NY
Here's one with the molding on, before i put the sun visors on.
Top of the page Bottom of the page
Justinsane
Posted 2018-06-08 4:57 PM (#564834 - in reply to #562564)
Subject: RE: 56' Belvedere interior



25
Location: Binghamton NY
and before i put on the window frame moldings. I had to cut stress reliefs in that corner and wrap it around with glue too.



(20180520_143721 (2).jpg)



Attachments
----------------
Attachments 20180520_143721 (2).jpg (458KB - 5 downloads)
Top of the page Bottom of the page
56D500boy
Posted 2018-06-08 6:01 PM (#564839 - in reply to #564772)
Subject: RE: 56' Belvedere interior



Expert

Posts: 3226
2000100010010025
Location: Lower Mainland BC
Justinsane - 2018-06-07 10:18 PM
The interior upholstery panels i got were in bad condition but in good enough condition to be restored. The backing board was warped and most of the fasteners were ripped out so i had to make new panels using the old ones as templates. I had to soak the old ones and flatten them back out so i could trace the outline and holes. I used 1/8" masonite or hardboard.They sell it in 4' X 8' sheets at home depot.


I like your thread. Congrats on the good work.

I too had to remake door panels. I also used 1/8" Masonite. Cutting the rectangular holes for the spring clips was a lot of fun (NOT). After I finished the first panel, I bought a pre-made set (cardboard) off eBay.

My door panel thread: http://www.forwardlook.net/forums/forums/thread-view.asp?tid=64288&...

Mine during the construction process, a test fit before I put the "skin" back on.



Edited by 56D500boy 2018-06-08 6:03 PM
Top of the page Bottom of the page
57DODGECONV
Posted 2018-06-08 7:47 PM (#564848 - in reply to #562564)
Subject: Re: 56' Belvedere interior


Elite Veteran

Posts: 625
50010025
Wow nice job on all your Interior ,Everything looks Great.
Top of the page Bottom of the page
Old Ray
Posted 2018-06-08 8:47 PM (#564856 - in reply to #564773)
Subject: RE: 56' Belvedere interior



Veteran

Posts: 295
100100252525
Location: Invermere B.C. Canada - Rocky Mountains

Justinsane - 2018-06-07 8:28 PM before i glued the padding and vinyl on.


Justin, looks good, what did you use for padding and how thick was it?
I got some fake tan Naugahyde with a pattern in it at a local fabric store and I am looking forward very much to doing the panels.
Thanks, Ray,

Top of the page Bottom of the page
Old Ray
Posted 2018-06-11 9:38 AM (#565018 - in reply to #564856)
Subject: RE: 56' Belvedere interior



Veteran

Posts: 295
100100252525
Location: Invermere B.C. Canada - Rocky Mountains
Justin, I tired to delete or edit my message, I couldn't. I found some padding, thanks anyways.
Top of the page Bottom of the page
Justinsane
Posted 2018-06-12 9:43 PM (#565103 - in reply to #564839)
Subject: RE: 56' Belvedere interior



25
Location: Binghamton NY
Awesome man, i checked out your thread. We went through the same thing. Did you end up stapling your vinyl on after you glued it and wraped it around the masonite? Because i used 1/8 board, i couldn't find any staples anyplace! The shortest at hardware stores are 1/4". I bought a stapler from the fabric store that takes staples like the ones for paper but a little more heavy duty, but most of them poked through so i pulled them out.
Top of the page Bottom of the page
56D500boy
Posted 2018-06-13 12:58 AM (#565108 - in reply to #565103)
Subject: RE: 56' Belvedere interior



Expert

Posts: 3226
2000100010010025
Location: Lower Mainland BC
I don't think 1/8" staples exist

Top of the page Bottom of the page
wizard
Posted 2018-06-13 2:24 AM (#565109 - in reply to #562564)
Subject: Re: 56' Belvedere interior



Board Moderator & Exner Expert 10K+

Posts: 11389
500050001000100100100252525
Location: Southern Sweden - Sturkö island
No problem, I've made my own 1/8" staples out of longer ones by cutting them with a sharp nippers. Just work on a lenght of approximately 1/2" of staple stick.


Very nice work on the interior!
Top of the page Bottom of the page
Justinsane
Posted 2018-06-13 10:30 PM (#565123 - in reply to #562564)
Subject: Re: 56' Belvedere interior



25
Location: Binghamton NY
I've seen 5/32 staples from upholstery supply stores but it doesn't look like they go into the typical staplers sold at hardware stores. I tried nipping and grinding but had no luck. I got enough in to hold the corners where it overlaps and is thicker. I might just buy one of those staplers. I'll let you guys know what i find and how it works..
Top of the page Bottom of the page
Jump to page : 1
Now viewing page 1 [50 messages per page]
Jump to forum :
Search this forum
Printer friendly version
E-mail a link to this thread


(Delete all cookies set by this site)