The Forward Look Network
The Forward Look Network
Search | Statistics | User Listing Forums | Chat | eBay | Calendars | Albums | Skins | Language
You are logged in as a guest. ( logon | register )

LA 318
Jump to page : 1
Now viewing page 1 [50 messages per page]
View previous thread :: View next thread
   Forward Look Technical Discussions -> General Technical Discussion and TroubleshootingMessage format
 
59 in Calif
Posted 2018-11-10 5:16 PM (#573287)
Subject: LA 318


Elite Veteran

Posts: 1080
1000252525
Location: Hayward, Calif
Hey Guys, Is the crankshaft rear flange the same on 70's - 80's LA318. In other words can a torque converter or a standard shift flywheel bolt up to it ? Also does it use the same vibration damper whether a torgue converter or a std shift flywheel is used? Thanks, Jerry
Top of the page Bottom of the page
Mopar1
Posted 2018-11-10 8:59 PM (#573296 - in reply to #573287)
Subject: Re: LA 318



Expert

Posts: 2687
2000500100252525
Location: N.W. Fla.
Same as what? 70s-80s engines are the same for those years. Different crank vs OEM FL cars
Top of the page Bottom of the page
59 in Calif
Posted 2018-11-10 9:48 PM (#573298 - in reply to #573287)
Subject: Re: LA 318


Elite Veteran

Posts: 1080
1000252525
Location: Hayward, Calif
I have an 1980' s LA318 that was bolted to a T/F trans. I have a friend who has a 73 Dodge PU truck with a truck 4 speed std trans. who could use this eng as long as there are no issues with putting a std shift trans flywheel to this eng. crank flange. I don't think there are any interchange issues, but was just looking for verification. Jerry
Top of the page Bottom of the page
58coupe
Posted 2018-11-11 10:57 AM (#573313 - in reply to #573287)
Subject: Re: LA 318



Expert

Posts: 1283
1000100100252525
Location: Alaska
The 62 and newer cranks have the same bolt pattern and you can bolt the standard flywheel to them BUT most crankshafts for an auto are not drilled for the pilot bearing.
There is a newer pilot bearing used by Mopar that fits in the end of the crank but the trans. input shaft has to be shortened to use it. The part number for this bearing is
listed somewhere on this site.
,
Top of the page Bottom of the page
57chizler
Posted 2018-11-12 4:26 PM (#573409 - in reply to #573313)
Subject: Re: LA 318



Expert

Posts: 3058
200010002525
Location: NorCal
Most crankshafts of that era are pilot drilled but not finish reamed for a pilot bushing unless a standard trans is installed; for unfinished cranks the above mentioned pilot bearing can usually be used. I have seen cases where standard shift cranks are not machined for a converter pilot hub.

So, as always with Mopar, ya never know until........
Top of the page Bottom of the page
59 in Calif
Posted 2018-11-13 12:42 AM (#573426 - in reply to #573287)
Subject: Re: LA 318


Elite Veteran

Posts: 1080
1000252525
Location: Hayward, Calif
Thanks Guys, I checked the end of this crank and it is drilled for a pilot brg. It is still bolted to an eng. stand so was a little hard to tell if the hole was finished. There was no id # on the block so had to research it by the casting #. Looks like it is about an 1985 Chry eng. Jerry
Top of the page Bottom of the page
Jump to page : 1
Now viewing page 1 [50 messages per page]
Jump to forum :
Search this forum
Printer friendly version
E-mail a link to this thread



(Delete all cookies set by this site)