The Forward Look Network
The Forward Look Network
Search | Statistics | User Listing Forums | Chat | eBay | Calendars | Albums | Skins | Language
You are logged in as a guest. ( logon | register )

55-56 Ball and Trunion Sizes and PNs
Jump to page : 1
Now viewing page 1 [50 messages per page]
View previous thread :: View next thread
   Forward Look Technical Discussions -> Transmission and Rear AxleMessage format
 
56D500boy
Posted 2019-06-05 9:24 PM (#582991)
Subject: 55-56 Ball and Trunion Sizes and PNs



Expert

Posts: 4651
200020005001002525
Location: Lower Mainland BC
Based on another thread, I found out (the hard way) that for 55-56 there were three different sizes of front ball and trunion front universal joint housings: 3.75", 4" and 4.25" (or by another source (an eBay advert), "the flange sizes were 3 5/8"...4"...4 3/8".

The smallest ones (3.75" (ish)) were typically used with the lower horsepower engines, either the 6 cylinder cars or the ones with the small V8 (e.g. Coronet V8 base). There were two ball and trunion U-joints on those cars, one at the front and one at the rear. Both of these small housing ball and trunion U-joints were spring loaded to allow for the centering - front/rear, of the drive shaft as the rear diff moved up and down with the road. The housing PN for the 55-56 6 cylinder cars was 1550 456. For the 55-56 Plymouth V8, Dodge D63-1 (Coronet small V8), and the 55 Desoto S22 and 55 Chrysler C67 (except Estate Wagons), the PN for the spring loaded housing was 1534 428. I've only seen either the 1550 456 or the 1534 428 housings so I don't really know the difference (if any). Both are small and spring loaded

The middle sized (4") housing had a PN of 1635 099 and was used by the 1956 Plymouth Fury, the 56 Dodge D63-2 (Royal 315 poly), 56 Dodge D63-3(Custom Royal 315 poly) and the D500 (315 hemi), and the 56 DeSoto S23 Firedome and the 56 Chrysler C71 Windsor. For these cars the rear U-joint was an "earred" cross-type that bolted to the pinion flange. All the slack and movement as taken up by the front ball and trunion.

This leaves the largest (4.25" or 4 3/8") housings. Its PN seems to be 1532 899 and in 55-56 was used by the Desoto S21, S22 and S24, and the Chrysler C67, C68, C69, C71 w/Power Pkg. and the C72, and all the wagons (which presumably were V8 (not sure about a 6 cyl Dodge or Plymouth wagon).

The 55-56 joint service package PN for the small housing ball and trunions, i.e. for the Front and Rear, of the D62, D63-1, All, S22, C67, except the wagon(s), was 1603 398. For the 4" housing, i.e. 56 P29 Fury, D63, S23 and C71, was 1643 287. For the biggest housing (for the S21, S24, S22, the Estate wagons, and the C67, C68, C69, and the C71 w/o Power Pkg. and the C72) the service package PN seems to be 1450 446. There are also some other PNs for the larger and more powerful Chryslers but I have no way to figure out what is what. See attached PN listings.



REFERENCES:

http://www.forwardlook.net/forums/forums/thread-view.asp?tid=71303&...



Edited by 56D500boy 2019-06-06 11:39 AM




(BallAndTrunionHousingPNs.jpg)



(BallAndTrunionJointPackagePNs.jpg)



Attachments
----------------
Attachments BallAndTrunionHousingPNs.jpg (191KB - 1 downloads)
Attachments BallAndTrunionJointPackagePNs.jpg (199KB - 1 downloads)
Top of the page Bottom of the page
Cmangeot
Posted 2019-06-06 9:19 AM (#583016 - in reply to #582991)
Subject: Re: 55-56 Ball and Trunion Sizes and PNs


Extreme Veteran

Posts: 435
10010010010025
Location: Park Hills, KY
Interesting, as I was just going to post a thread requesting whether this will fit my 1960 Windsor

https://www.ebay.com/itm/NOS-D65-Mopar-4-U-Joint-Kit-Universal-1957-...

Top of the page Bottom of the page
56D500boy
Posted 2019-06-06 12:12 PM (#583025 - in reply to #583016)
Subject: Re: 55-56 Ball and Trunion Sizes and PNs



Expert

Posts: 4651
200020005001002525
Location: Lower Mainland BC
Cmangeot - 2019-06-06 6:19 AM

Interesting, as I was just going to post a thread requesting whether this will fit my 1960 Windsor


First thing you need to do is confirm that your existing flange is 4" in diameter. Otherwise, that looks like a good deal considering that it is everything needed (if it is the right size)

Top of the page Bottom of the page
Jump to page : 1
Now viewing page 1 [50 messages per page]
Jump to forum :
Search this forum
Printer friendly version
E-mail a link to this thread



(Delete all cookies set by this site)