The Forward Look Network
The Forward Look Network
Search | Statistics | User Listing Forums | Chat | eBay | Calendars | Albums | Skins | Language
You are logged in as a guest. ( logon | register )

413 engine
Jump to page : 1
Now viewing page 1 [50 messages per page]
View previous thread :: View next thread
   Forward Look Technical Discussions -> General Technical Discussion and TroubleshootingMessage format
 
johnfin
Posted 2019-08-26 10:30 AM (#586575)
Subject: 413 engine


Regular

Posts: 95
252525
any of you seen machine shop engine specs online? like cylinder bore taper, piston allowence, etc. cant seem to find anything.
Top of the page Bottom of the page
57chizler
Posted 2019-08-26 3:06 PM (#586590 - in reply to #586575)
Subject: RE: 413 engine



Expert

Posts: 3264
200010001001002525
Location: NorCal
It's all in the FSM; for instance:



(Bore.PNG)



Attachments
----------------
Attachments Bore.PNG (18KB - 16 downloads)
Top of the page Bottom of the page
johnfin
Posted 2019-09-22 8:48 PM (#587856 - in reply to #586575)
Subject: RE: 1960 413 engine


Regular

Posts: 95
252525
There seems to be a conflict with bearings and part numbers. Crank journals are the same as the 440 but some manufacturers like clevite list different part numbers. ebay has bearings and use generic specs, 1959-1974 383-440. What gives?
Top of the page Bottom of the page
BigBlockMopar
Posted 2019-09-23 6:10 AM (#587866 - in reply to #586575)
Subject: Re: 413 engine



Expert

Posts: 3551
200010005002525
Location: Netherlands
Later 440-engines have a main trust-bearing with larger trust-faces then the earlier years.
The 'Earlier' small trust-face bearings fit all the 413/440's.
The large trust-face bearings only fit the later 440's.

Perhaps that's where the difference in partnumbers come from.

Rod-bearings should be all the same in stock form, but a range of bearings are made presently that have a large camfer on one side (or are just narrower overall) to accomodate a bigger crank radius. Mainly used on stroker cranks.
Top of the page Bottom of the page
Powerflite
Posted 2019-09-23 3:14 PM (#587885 - in reply to #586575)
Subject: Re: 413 engine



Expert 5K+

Posts: 5818
5000500100100100
Location: So. California
Thanks for the great info Herman! Good to keep in mind.
Top of the page Bottom of the page
johnfin
Posted 2019-09-23 7:12 PM (#587888 - in reply to #586575)
Subject: RE: 413 engine


Regular

Posts: 95
252525
the federal mogal rod bearings are sold as unplated and resizeable. What does that mean?
Top of the page Bottom of the page
57chizler
Posted 2019-09-24 3:53 PM (#587912 - in reply to #587888)
Subject: RE: 413 engine



Expert

Posts: 3264
200010001001002525
Location: NorCal
Most rod/main bearings have a thin plate of tin over the babbit subsurface, the tin is the actual bearing surface. Once installed, un-plated bearings can be bored or honed slightly to adjust the bore size.
Top of the page Bottom of the page
johnfin
Posted 2019-09-24 6:33 PM (#587913 - in reply to #586575)
Subject: RE: 413 engine


Regular

Posts: 95
252525
clear as mud!!
Top of the page Bottom of the page
57chizler
Posted 2019-09-25 1:30 PM (#587940 - in reply to #587913)
Subject: RE: 413 engine



Expert

Posts: 3264
200010001001002525
Location: NorCal
Tennis anyone?
Top of the page Bottom of the page
Jump to page : 1
Now viewing page 1 [50 messages per page]
Jump to forum :
Search this forum
Printer friendly version
E-mail a link to this thread



(Delete all cookies set by this site)