|
 PSA: Please remember to lubricate and exercise your cowl vent hingesJump to page : 1 Now viewing page 1 [50 messages per page] | View previous thread :: View next thread |
| Forward Look Technical Discussions -> General Technical Discussion and Troubleshooting | Message format |
56D500boy |
| ||
Exner Expert 10K+ Posts: 10354    Location: Lower Mainland BC | . You want to do this because you do NOT want to go through the nightmare of replacing a broken cowl vent hinge, like I had to. Much easier to remove the bug screen and use one of those red "straw" nozzles on your favourite rust removing lubricant (PB Blaster, Liquid Wrench, Moovit, Mopar Combustion chamber cleaner, WD40, etc) to spray lubricant onto the two hinge points and then, after bit of soaking time, using the cowl vent lever to exercise the cowl vent a few times. Then repeat a couple of more times before re-installing the bug screen. You will be much happier than the alternative, trust me.  This thread: http://www.forwardlook.net/forums/forums/thread-view.asp?tid=65057 Example 56 Cowl Vent diagram:  Edited by 56D500boy 2019-09-08 9:14 PM | ||
| |||
| 71charger_fan |
| ||
Elite Veteran Posts: 669  Location: Frederick, MD | |||
| |||
| 56D500boy |
| ||
Exner Expert 10K+ Posts: 10354 Location: Lower Mainland BC | 71charger_fan - 2019-09-15 5:37 PM I second that. What a PITA when the hinge breaks from metal fatigue. Terrance: Agree. Your solution for your 55 Plymouth was probably better/easier than my solution, *HOWEVER* yours involved the removal of the heater duct and, while I knew that, I did NOT want to open another potential can of worms just now. Hence my "laproscopic surgery" (blind) approach.  Could you find and post the photos from your solution here so they could be more easily found by the next victim of this issue in the future? (Please) | ||
| |||
| 71charger_fan |
| ||
Elite Veteran Posts: 669 Location: Frederick, MD | I couldn't find them on my computer, so I just downloaded them from my thread on this site. (Plaza Cowl.jpg) (Plaza Cowl (1).jpg) (Plaza Cowl Vent.jpg) (Plaza Cowl Vent Rod Bellows.jpg) (Plaza Cowl Vent (3).jpg) (Plaza Cowl Vent (4).jpg) (Plaza Cowl Vent Rod.jpg) (Plaza Cowl Vent Hinge Broken.jpg) (Plaza Cowl Vent Hinge.jpg) (Plaza Cowl Vent Hinge Repair.jpg) (Plaza Cowl Vent Hinge Repair (2).jpg) (Plaza Cowl Vent Hinge Repair (3).jpg) (Plaza Cowl Vent Hinge Repair (4).jpg) (Plaza Cowl Vent Hinge Repair (5).jpg) (Plaza Cowl Vent Hinge Repair (6).jpg) (Plaza Cowl Vent (2).jpg) Attachments ----------------  Plaza Cowl.jpg (143KB - 221 downloads) Plaza Cowl (1).jpg (86KB - 220 downloads) Plaza Cowl Vent.jpg (153KB - 217 downloads) Plaza Cowl Vent Rod Bellows.jpg (126KB - 230 downloads) Plaza Cowl Vent (3).jpg (91KB - 216 downloads) Plaza Cowl Vent (4).jpg (96KB - 231 downloads) Plaza Cowl Vent Rod.jpg (124KB - 221 downloads) Plaza Cowl Vent Hinge Broken.jpg (103KB - 227 downloads) Plaza Cowl Vent Hinge.jpg (108KB - 220 downloads) Plaza Cowl Vent Hinge Repair.jpg (56KB - 227 downloads) Plaza Cowl Vent Hinge Repair (2).jpg (57KB - 228 downloads) Plaza Cowl Vent Hinge Repair (3).jpg (64KB - 227 downloads) Plaza Cowl Vent Hinge Repair (4).jpg (85KB - 228 downloads) Plaza Cowl Vent Hinge Repair (5).jpg (99KB - 219 downloads) Plaza Cowl Vent Hinge Repair (6).jpg (102KB - 226 downloads) Plaza Cowl Vent (2).jpg (108KB - 224 downloads) | ||
| |||
| 56D500boy |
| ||
Exner Expert 10K+ Posts: 10354 Location: Lower Mainland BC | Thanks for re-posting your photos Terrance. Reviewing them, I would say that your solution is better than mine in the sense that a) it doesn't require drilling holes in the cowl and b) I think that bolt that you attached the hinge point-strap to *IS* accessible even with the heater duct/box still attached. Good job. That said, getting that hinge point strap just right must have been a challenge. Thanks. Again folks, make sure that you lubricate and exercise your cowl vent hinges - or suffer the consequences. | ||
| |||
| 56D500boy |
| ||
Exner Expert 10K+ Posts: 10354 Location: Lower Mainland BC | 56D500boy - 2019-09-16 9:12 AM Again folks, make sure that you lubricate and exercise your cowl vent hinges - or suffer the consequences. Bump. Lube lube lube Nobody wants a broken cowl vent hinge. | ||
| |||
| mikes2nd |
| ||
Expert 5K+ Posts: 5116 | |||
| |||
| 56D500boy |
| ||
Exner Expert 10K+ Posts: 10354 Location: Lower Mainland BC | mikes2nd - 2024-12-07 8:46 AM ooof.. You sir have a rusty cowl issue... Shame... That was 71charger_fan's (Terrance's) 55 Plymouth wagon. In my defense, this is what I started with: And this is what it eventually looked like: REFERENCE: http://www.forwardlook.net/forums/forums/thread-view.asp?tid=65057&... | ||
| |||
| Jump to page : 1 Now viewing page 1 [50 messages per page] |
| Search this forum Printer friendly version E-mail a link to this thread |
| (Delete all cookies set by this site) | |
