The Forward Look Network
The Forward Look Network
Search | Statistics | User Listing Forums | Chat | eBay | Calendars | Albums | Skins | Language
You are logged in as a guest. ( logon | register )

Help needed console parts 300G
Jump to page : 1
Now viewing page 1 [50 messages per page]
View previous thread :: View next thread
   Forward Look Technical Discussions -> Body, Glass, Interior and TrimMessage format
 
matt
Posted 2019-12-27 2:26 AM (#592069)
Subject: Help needed console parts 300G


Veteran

Posts: 132
10025
Location: Malmberget, Sweden
Can anyone measure the joint peace in the console for me


The F and G are the same.
Top of the page Bottom of the page
matt
Posted 2019-12-27 8:38 AM (#592081 - in reply to #592069)
Subject: Re: Help needed console parts 300G


Veteran

Posts: 132
10025
Location: Malmberget, Sweden
If anyone have a pic of the joint bit it would help.
Top of the page Bottom of the page
NicksGarage
Posted 2019-12-27 10:15 AM (#592083 - in reply to #592069)
Subject: RE: Help needed console parts 300G



Elite Veteran

Posts: 661
5001002525
Location: Ramona, CA
It's about 3 3/8" long. I can probably find a picture of the back side.





(console_trim_joint.jpg)



Attachments
----------------
Attachments console_trim_joint.jpg (78KB - 7 downloads)
Top of the page Bottom of the page
matt
Posted 2019-12-27 3:54 PM (#592093 - in reply to #592069)
Subject: Re: Help needed console parts 300G


Veteran

Posts: 132
10025
Location: Malmberget, Sweden
Thanx Nick. My car is in winter storage 150km from me
What the width of the part?
And what is the real name of that part?



Top of the page Bottom of the page
NicksGarage
Posted 2019-12-27 6:11 PM (#592103 - in reply to #592069)
Subject: RE: Help needed console parts 300G



Elite Veteran

Posts: 661
5001002525
Location: Ramona, CA
I'm not sure what the actual name of the part is. The parts book isn't much help. This is from the 1961 book.





(61_console_parts.png)



Attachments
----------------
Attachments 61_console_parts.png (21KB - 7 downloads)
Top of the page Bottom of the page
Mr. Bob
Posted 2019-12-28 5:39 PM (#592149 - in reply to #592069)
Subject: RE: Help needed console parts 300G


Member

Posts: 17

I have a pair of these that will go in my car when I finally do the interior this spring. I can't see a part number on them. They are indeed exactly 3 3/8 inches long. And 1 3/4" across. You can see their contour in the end view photo below. Each bend is about 1/4" from the side. The high bend on the left is 9/16" of the table top, the low bend on the right is 7/16" off the surface.

The shop working on my car is called Heavy Metal Custom Shop, because they can fabricate almost anything from metal. If you'd like, I can take one of my pieces to them and get an estimate on how much it would cost for them to fabricate a pair of these for you. They would also have my front and rear consoles to test fit them to. Getting the inner clips just right will probably be the most difficult (expensive) part of the job.



(300G console trim - end view.jpg)



(300G console trim - end view 2.jpg)



(300G console trim - back side.jpg)



(300G console trim - inside clips.jpg)



Attachments
----------------
Attachments 300G console trim - end view.jpg (171KB - 7 downloads)
Attachments 300G console trim - end view 2.jpg (123KB - 7 downloads)
Attachments 300G console trim - back side.jpg (139KB - 7 downloads)
Attachments 300G console trim - inside clips.jpg (117KB - 7 downloads)
Top of the page Bottom of the page
NicksGarage
Posted 2019-12-28 7:06 PM (#592150 - in reply to #592069)
Subject: Re: Help needed console parts 300G



Elite Veteran

Posts: 661
5001002525
Location: Ramona, CA
Great pictures, saves me digging up mine. It looks like those tabs were part of a continuous extrusion that they ground off the excess.
Top of the page Bottom of the page
Jump to page : 1
Now viewing page 1 [50 messages per page]
Jump to forum :
Search this forum
Printer friendly version
E-mail a link to this thread



(Delete all cookies set by this site)