The Forward Look Network
The Forward Look Network
Search | Statistics | User Listing Forums | Chat | eBay | Calendars | Albums | Skins | Language
You are logged in as a guest. ( logon | register )

1960 Chrysler 383 questions
Jump to page : 1
Now viewing page 1 [50 messages per page]
View previous thread :: View next thread
   Forward Look Technical Discussions -> The Exhaust Pipe - Modification & PerformanceMessage format
 
58Jackie
Posted 2019-12-31 5:43 PM (#592317)
Subject: 1960 Chrysler 383 questions



Veteran

Posts: 123
100
Location: Southern Idaho, USA
Hey guys, I'm hoping some of you can help me out with this. I just found a '60 Chrysler with a 383 in it in a junkyard; i am serious about getting the motor from it. It says "Golden Lion 383" on the valve covers. Its complete, top to bottom. Has a 2 barrel carb on it. From what i can tell (still in car) it has very little rust in the block.

I need some questions answered before i buy the motor;

I didnt know 383s were out in 1960 (how rare are these); is this a different version of the later 383s. Like for say, the 318 Polys vs. the later 318 la type?
So can this motor be easily rebuilt regarding parts availability for it?
Is this the RB or the other low-deck block?
Top of the page Bottom of the page
wizard
Posted 2019-12-31 6:22 PM (#592320 - in reply to #592317)
Subject: Re: 1960 Chrysler 383 questions



Board Moderator & Exner Expert 10K+

Posts: 13042
500050002000100025
Location: Southern Sweden - Sturkö island
You found a Windsor engine.
It's RB and not rare.
Yes it can be rebuilt.

For confirmation that it is the 60 RB engine post a photo of the left cylinder bank front where the stamped numbers are
Top of the page Bottom of the page
58Jackie
Posted 2019-12-31 11:10 PM (#592332 - in reply to #592320)
Subject: Re: 1960 Chrysler 383 questions



Veteran

Posts: 123
100
Location: Southern Idaho, USA
To clarify, what i meant in terms of rebuilding is I'd like to know what kind of parts interchangeability there is for the 383 rb. Apparently the 383 rb was used only in Chryslers from 59-60; then on it went to the standard b-series 383. And thats all the parts I've been able to find is just for the b-series 383.

I'm on the fence of buying this motor i found due to this, now if i could find all the parts i need for it, or knew more about it, I'd have it right now as it seems like a pretty cool motor.
Top of the page Bottom of the page
Dave L.
Posted 2020-01-01 1:15 AM (#592334 - in reply to #592332)
Subject: Re: 1960 Chrysler 383 questions



Extreme Veteran

Posts: 340
10010010025
Location: Tacoma, WA
The 383RB was the standard engine in the 1960 Windsor and Saratoga; two and four barrel versions respectively. Golden Lion was just a marketing term of the time. The reason behind the 383RB, which is really just a smaller-bore 413, is not very exciting, it came down to production capabilities, as described in several articles, like this one on Allpar. https://www.allpar.com/history/inside/plymouth-7a.html
(Which poses an interesting question, why pick 383?) Pistons are hard to come by. Even Egge currently only lists them for standard bore. So on mine, I'm hoping to be able salvage a block and pistons out of the two engines I have.

Edited by Dave L. 2020-01-01 1:32 AM
Top of the page Bottom of the page
Powerflite
Posted 2020-01-01 1:40 PM (#592344 - in reply to #592317)
Subject: Re: 1960 Chrysler 383 questions



Expert 5K+

Posts: 9604
500020002000500100
Location: So. Cal
I think pistons are the only issue with them. The 350 motor had a bore of 4.06, so you could use those with a .03" overbore. That's about perfect. However, the piston height may not be correct and I'm not sure how available those are either. If you offset grind the crank to give you more stroke, you may be able to make the piston height work out well. You'll have to calculate it out. Or you can use custom pistons for about $800. If you go to the trouble of going with custom pistons, you might as well stroke the crank using BB Chevy rods if you would like to get more cubic inches out of it. The nice thing about a long stroke 383 RB with the small bore is you can couple that with a very high rear gear or overdrive, and you can potentially get very good gas mileage out of the car, relative to the size of the motor. The long stroke gives you more low end torque that you would need to lumber around with high gears at very low rpm. Otherwise, you could install a 413 or 440 cheaper and few people would know the difference, with the resulting lower gas mileage.
Top of the page Bottom of the page
NicksGarage
Posted 2020-01-02 11:48 AM (#592379 - in reply to #592317)
Subject: RE: 1960 Chrysler 383 questions



Expert

Posts: 1223
1000100100
Location: Ramona, CA
58Jackie - 2019-12-31 2:43 PM

Hey guys, I'm hoping some of you can help me out with this. I just found a '60 Chrysler with a 383 in it in a junkyard; i am serious about getting the motor from it. It says "Golden Lion 383" on the valve covers. Its complete, top to bottom. Has a 2 barrel carb on it. From what i can tell (still in car) it has very little rust in the block.

I need some questions answered before i buy the motor;

I didnt know 383s were out in 1960 (how rare are these); is this a different version of the later 383s. Like for say, the 318 Polys vs. the later 318 la type?
So can this motor be easily rebuilt regarding parts availability for it?
Is this the RB or the other low-deck block?


Like mentioned above, it would have come in a Windsor. What's left of the rest of the car and what body style is it? I'm looking for some wagon parts.

Top of the page Bottom of the page
Cmangeot
Posted 2020-01-02 1:46 PM (#592387 - in reply to #592379)
Subject: Re: 1960 Chrysler 383 questions


Extreme Veteran

Posts: 531
50025
Location: Park Hills, KY
Gee....good thing my 60 Windsor only has 43K miles on it. Sounds like it won't be easy to rebuild if I ever have an issue.
Top of the page Bottom of the page
NicksGarage
Posted 2020-01-02 1:57 PM (#592388 - in reply to #592387)
Subject: Re: 1960 Chrysler 383 questions



Expert

Posts: 1223
1000100100
Location: Ramona, CA
Cmangeot - 2020-01-02 10:46 AM

Gee....good thing my 60 Windsor only has 43K miles on it. Sounds like it won't be easy to rebuild if I ever have an issue.


If you maintain it, it should last forever.
Top of the page Bottom of the page
Powerflite
Posted 2020-01-02 2:27 PM (#592392 - in reply to #592317)
Subject: Re: 1960 Chrysler 383 questions



Expert 5K+

Posts: 9604
500020002000500100
Location: So. Cal
Running the right fuel ratio will help the rings the most. That's one of the benefits of fuel injection, to better ensure that.
Top of the page Bottom of the page
wayfarer
Posted 2020-01-02 4:24 PM (#592394 - in reply to #592332)
Subject: Re: 1960 Chrysler 383 questions



Elite Veteran

Posts: 888
500100100100252525
Location: Peoples Republic of Oregon
58Jackie - 2019-12-31 8:10 PM

To clarify, what i meant in terms of rebuilding is I'd like to know what kind of parts interchangeability there is for the 383 rb. Apparently the 383 rb was used only in Chryslers from 59-60; then on it went to the standard b-series 383. And thats all the parts I've been able to find is just for the b-series 383.

I'm on the fence of buying this motor i found due to this, now if i could find all the parts i need for it, or knew more about it, I'd have it right now as it seems like a pretty cool motor.


Unless you are looking this engine for use in a pre-62 car then what is the appeal? There are still plenty of 400 and 440 engines to be found.
As mentioned, the biggest hurdle in rebuilding is getting pistons and forgings are the only reasonable option IMHO. RockAuto probably has most of the remaining rebuild parts.
Top of the page Bottom of the page
wizard
Posted 2020-01-02 4:28 PM (#592395 - in reply to #592317)
Subject: Re: 1960 Chrysler 383 questions



Board Moderator & Exner Expert 10K+

Posts: 13042
500050002000100025
Location: Southern Sweden - Sturkö island
My 383 engine has roundabout 160k now and still running good.

As Nick wrote - maintainence is the key.
Top of the page Bottom of the page
1960fury
Posted 2020-01-03 6:46 AM (#592414 - in reply to #592388)
Subject: Re: 1960 Chrysler 383 questions



Expert 5K+

Posts: 7385
50002000100100100252525
Location: northern germany
NicksGarage - 2020-01-02 1:57 PM

Cmangeot - 2020-01-02 10:46 AM

Gee....good thing my 60 Windsor only has 43K miles on it. Sounds like it won't be easy to rebuild if I ever have an issue.


If you maintain it, it should last forever.


Correct
Top of the page Bottom of the page
60 dart
Posted 2020-01-04 12:08 AM (#592442 - in reply to #592317)
Subject: Re: 1960 Chrysler 383 questions



Expert 5K+

Posts: 8947
50002000100050010010010010025
Location: WHEELING,WV.>>>HOME OF WWVA
do yourself a favor , unless you're wanting to build a points car go with a B-383 setup . you will be glad to did! ----------------------------------------------------------later
Top of the page Bottom of the page
Cmangeot
Posted 2020-01-05 2:43 PM (#592500 - in reply to #592442)
Subject: Re: 1960 Chrysler 383 questions


Extreme Veteran

Posts: 531
50025
Location: Park Hills, KY
I change plugs and oil every 2000 miles. Let’s hope that helps. ??
Top of the page Bottom of the page
1960fury
Posted 2020-01-05 3:03 PM (#592502 - in reply to #592500)
Subject: Re: 1960 Chrysler 383 questions



Expert 5K+

Posts: 7385
50002000100100100252525
Location: northern germany
Cmangeot - 2020-01-05 2:43 PM

I change plugs and oil every 2000 miles. Let’s hope that helps. ??


That is a "bit" much! Use quality synthetic oil, let it always reach operating temperature and change every 6-8k. Also everytime you change the filter, it runs for several seconds without oil pressure. Very bad. I change the oil every 2 years or so, way above 8k between changes, yet I always build up oil pressure with an electric dill before I start it.
Top of the page Bottom of the page
Cmangeot
Posted 2020-01-06 6:51 PM (#592555 - in reply to #592317)
Subject: Re: 1960 Chrysler 383 questions


Extreme Veteran

Posts: 531
50025
Location: Park Hills, KY
Great advice.
Top of the page Bottom of the page
58Jackie
Posted 2020-01-09 6:20 PM (#592699 - in reply to #592394)
Subject: Re: 1960 Chrysler 383 questions



Veteran

Posts: 123
100
Location: Southern Idaho, USA
wayfarer - 2020-01-02 3:24 PM

58Jackie - 2019-12-31 8:10 PM

To clarify, what i meant in terms of rebuilding is I'd like to know what kind of parts interchangeability there is for the 383 rb. Apparently the 383 rb was used only in Chryslers from 59-60; then on it went to the standard b-series 383. And thats all the parts I've been able to find is just for the b-series 383.

I'm on the fence of buying this motor i found due to this, now if i could find all the parts i need for it, or knew more about it, I'd have it right now as it seems like a pretty cool motor.


Unless you are looking this engine for use in a pre-62 car then what is the appeal? There are still plenty of 400 and 440 engines to be found.
As mentioned, the biggest hurdle in rebuilding is getting pistons and forgings are the only reasonable option IMHO. RockAuto probably has most of the remaining rebuild parts.


Well i was planning to put this motor into my 58 Belvedere, as i think this motor would be a little bit closer to original than a 440 from the 60s or 70s. But since you guys informed me that this 383 is going to be a bit of a challenge with the bottom end, i think i'll just stay with the 440.
Top of the page Bottom of the page
BlueGhost
Posted 2020-01-10 3:56 PM (#592752 - in reply to #592317)
Subject: Re: 1960 Chrysler 383 questions



Regular

Posts: 58
2525
Location: League City, TX
You may want the crank out of the 383, if you are looking to mate your 440 to a push button transmission.
Top of the page Bottom of the page
Jump to page : 1
Now viewing page 1 [50 messages per page]
Jump to forum :
Search this forum
Printer friendly version
E-mail a link to this thread

* * * This site contains affiliate links for which we may be compensated * * *


(Delete all cookies set by this site)