The Forward Look Network
The Forward Look Network
Search | Statistics | User Listing Forums | Chat | eBay | Calendars | Albums | Skins | Language
You are logged in as a guest. ( logon | register )

55 Chrysler trans shifter shaft seal replacement
Jump to page : 1
Now viewing page 1 [50 messages per page]
View previous thread :: View next thread
   Forward Look Technical Discussions -> Transmission and Rear AxleMessage format
 
ram300
Posted 2021-02-04 5:10 PM (#608535)
Subject: 55 Chrysler trans shifter shaft seal replacement



Extreme Veteran

Posts: 363
1001001002525
Has anyone had success installing a new seal where the shifter/kickdown shaft enters the trans on a 55 Chrysler Powerflite WITHOUT removing the trans from the car? Is it possible?

Also if anybody is able to give me size/ part number of that seal.

Thanks
Owen
Top of the page Bottom of the page
56D500boy
Posted 2021-02-04 7:31 PM (#608540 - in reply to #608535)
Subject: RE: 55 Chrysler trans shifter shaft seal replacement



Expert 5K+

Posts: 9855
5000200020005001001001002525
Location: Lower Mainland BC
.
From a previous thread, I wrote:

"Based on this photo in my previous post, while I was back in the garage tinkering on my 56 Dodge, I decided to check the Powerflite more carefully.



I wiped the area off with a solvent soaked paper towel and discovered that there is a seal there for sure. It is marked 50018, SN (or NS?) and Pat. Pend. I measured a shaft diameter of 0.62" and an overall seal diameter of about 1.29" (give or take).

When I used the SKF parts search, a 50018 comes up as a National Mfg. Part Number: 50018 with a cross to a 6925 from National, Federal Mogul and Caterpillar. Dimensions are very close to what I measured and given that I didn't necessarily get the outside diameter measured correctly, I would believe the 1.254" more than my 1.29"

I think that the OE P/N for that seal is 1408 353 but the SKF interchange does not recognize the number. However when you Google "1408353 powerflite manual shaft seal" a bunch of hits come up, including one a MoparMall labeled 50018. Bingo. "

https://www.moparmall.com/product-p/kc-81204.htm









REFERENCE: http://www.forwardlook.net/forums/forums/thread-view.asp?tid=73997&...



Edited by 56D500boy 2021-02-04 7:41 PM
Top of the page Bottom of the page
ronbo97
Posted 2021-02-04 8:29 PM (#608541 - in reply to #608535)
Subject: Re: 55 Chrysler trans shifter shaft seal replacement


Expert

Posts: 4034
2000200025
Location: Connecticut
Try NAPA before overpaying (+ shipping) for the same seal at Atlas/MoparMall. SKF 6925 is 9.00.

Ron
Top of the page Bottom of the page
jhermis1861
Posted 2023-05-22 11:44 AM (#629734 - in reply to #608535)
Subject: RE: 55 Chrysler trans shifter shaft seal replacement


Member

Posts: 5

Did you happen to replace yours? I am needing to replace mine as its leaking there as well.. I have the 50018 seal but just not a transmission guy and don't want to drop the transmission just to replace a seal... If you replaced yours, any pointers you could give me...

Thanks,
Jon
Top of the page Bottom of the page
tmd171
Posted 2024-03-21 11:54 AM (#634331 - in reply to #608535)
Subject: Re: 55 Chrysler trans shifter shaft seal replacement


Member

Posts: 15

Were you able to replace yours? How did you remove your seal?
Thanks
Top of the page Bottom of the page
56D500boy
Posted 2024-03-21 1:29 PM (#634335 - in reply to #634331)
Subject: Re: 55 Chrysler trans shifter shaft seal replacement



Expert 5K+

Posts: 9855
5000200020005001001001002525
Location: Lower Mainland BC
.
It looks like a Lisle 58430 Shaft Type Seal Puller might work on these small seals in such a confined area.

https://www.lislecorp.com/specialty-tools/shaft-type-seal-puller



Top of the page Bottom of the page
dels56
Posted 2024-03-21 1:50 PM (#634337 - in reply to #608535)
Subject: Re: 55 Chrysler trans shifter shaft seal replacement


Extreme Veteran

Posts: 345
10010010025
Looks like a winner!
Del
Top of the page Bottom of the page
Jump to page : 1
Now viewing page 1 [50 messages per page]
Jump to forum :
Search this forum
Printer friendly version
E-mail a link to this thread

* * * This site contains affiliate links for which we may be compensated * * *


(Delete all cookies set by this site)