The Forward Look Network
The Forward Look Network
Search | Statistics | User Listing Forums | Chat | eBay | Calendars | Albums | Skins | Language
You are logged in as a guest. ( logon | register )

57-58 Plymouth/Dodge rear trunk stainless trim(back edge)
Jump to page : 1
Now viewing page 1 [50 messages per page]
View previous thread :: View next thread
   Forward Look Technical Discussions -> Body, Glass, Interior and TrimMessage format
 
mikes2nd
Posted 2022-02-19 9:44 PM (#619580)
Subject: 57-58 Plymouth/Dodge rear trunk stainless trim(back edge)


Expert 5K+

Posts: 5006
5000

I picked up what the guy said was the 57 plymouth rear trunk trim...  It actually appears about 3/4 inch wide.

I see the one guy charges 250$ for a 58-2 piece of simple trim and its pretty thin...  You could just use a 5$ 3m chrome/aluminum strip and it actually looks better... so yoinks...

but looks like I have a 57 trunk lid moulding and two dodge rear mouldings..

Anyone have a up close original pic of 58... The connector is very flat and no screw right?

 

 

 





(57DodgeTrunkTrim.jpg)



(58DodgeTrunkMoulding.jpg)



(58plytrunktrim.jpg)



(58Trunklid.jpg)



(moulding.jpg)



Attachments
----------------
Attachments 57DodgeTrunkTrim.jpg (87KB - 66 downloads)
Attachments 58DodgeTrunkMoulding.jpg (47KB - 70 downloads)
Attachments 58plytrunktrim.jpg (171KB - 73 downloads)
Attachments 58Trunklid.jpg (133KB - 72 downloads)
Attachments moulding.jpg (114KB - 68 downloads)
Top of the page Bottom of the page
mikes2nd
Posted 2022-02-19 9:47 PM (#619581 - in reply to #619580)
Subject: Re: 57-58 Plymouth/Dodge rear trunk stainless trim(back edge)


Expert 5K+

Posts: 5006
5000
This is the 57 wide one piece with the very slight bend in it, the ends fit into the 57 Tail light trim





(57SlightBend.jpg)



Attachments
----------------
Attachments 57SlightBend.jpg (215KB - 79 downloads)
Top of the page Bottom of the page
mikes2nd
Posted 2022-02-19 9:59 PM (#619582 - in reply to #619580)
Subject: Re: 57-58 Plymouth/Dodge rear trunk stainless trim(back edge)


Expert 5K+

Posts: 5006
5000
if you look at the second "Christine" the rear trim looks flat and its missing the edges... it looks like 57 trim for the center 3 pieces?

Since I have a couple 58 tail lights, maybe would be cool to use a 58 tail light with the 57 rear surround trim when i get around to my plymouth. The stainless reflects better.
Top of the page Bottom of the page
springsweptwing
Posted 2022-02-20 6:04 AM (#619591 - in reply to #619582)
Subject: Re: 57-58 Plymouth/Dodge rear trunk stainless trim(back edge)



Elite Veteran

Posts: 1140
100010025
Location: Blackpool, United Kingdom.
Hi Mike,


That 6010 029 trim for the Dodge is the same profile as the lower fin moulding and is rounded at the ends.

I am looking for one for my 58.

Thanks Paul.



(57DodgeTrunkTrim~2.jpg)



Attachments
----------------
Attachments 57DodgeTrunkTrim~2.jpg (90KB - 69 downloads)
Top of the page Bottom of the page
ronbo97
Posted 2022-02-20 11:42 AM (#619599 - in reply to #619591)
Subject: Re: 57-58 Plymouth/Dodge rear trunk stainless trim(back edge)


Expert

Posts: 4034
2000200025
Location: Connecticut

The three piece molding (two sides and a center cap) below the trunk on the 58 Plymouth are made from anodized aluminum. Dodge is probably stainless.

Ron

Top of the page Bottom of the page
springsweptwing
Posted 2022-02-20 4:20 PM (#619612 - in reply to #619599)
Subject: Re: 57-58 Plymouth/Dodge rear trunk stainless trim(back edge)



Elite Veteran

Posts: 1140
100010025
Location: Blackpool, United Kingdom.
ronbo97 - 2022-02-20 4:42 PM

The three piece molding (two sides and a center cap) below the trunk on the 58 Plymouth are made from anodized aluminum. Dodge is probably stainless.

Ron



Yes the Dodge is stainless, I think this is a joining piece for a Plymouth, it would be for 5/8 wide trim?



(IMG_20220220_211621885_copy_800x600.jpg)



(IMG_20220220_211637037_copy_800x600.jpg)



Attachments
----------------
Attachments IMG_20220220_211621885_copy_800x600.jpg (59KB - 65 downloads)
Attachments IMG_20220220_211637037_copy_800x600.jpg (98KB - 67 downloads)
Top of the page Bottom of the page
ronbo97
Posted 2022-02-20 6:25 PM (#619613 - in reply to #619612)
Subject: Re: 57-58 Plymouth/Dodge rear trunk stainless trim(back edge)


Expert

Posts: 4034
2000200025
Location: Connecticut

No. The center join has a screw hole in the middle. And it's aluminum. No idea what that is.

Ron

Top of the page Bottom of the page
Jump to page : 1
Now viewing page 1 [50 messages per page]
Jump to forum :
Search this forum
Printer friendly version
E-mail a link to this thread

* * * This site contains affiliate links for which we may be compensated * * *


(Delete all cookies set by this site)