The Forward Look Network | ||
| ||
57 New Yorker fenders Jump to page : 1 Now viewing page 1 [50 messages per page] | View previous thread :: View next thread |
Forward Look Swap Meet -> For Sale - PARTS | Message format |
finsruskw |
| ||
Expert Posts: 2289 Location: Eastern Iowa | 1 driver side fender and partial pass side fender from a 57 New Yorker. Fair condition. Pass side is missing headlamp section, rest of it is good for patch panels Driver side has H/L wiring intact. $250 for the pair FOB 52041, Iowa Thanks for the ad! (DSCN9753.JPG) (DSCN9755.JPG) (DSCN9756.JPG) (DSCN9757.JPG) (DSCN9758.JPG) (DSCN9759.JPG) (DSCN9760.JPG) Attachments ---------------- DSCN9753.JPG (216KB - 47 downloads) DSCN9755.JPG (214KB - 52 downloads) DSCN9756.JPG (225KB - 49 downloads) DSCN9757.JPG (229KB - 50 downloads) DSCN9758.JPG (202KB - 51 downloads) DSCN9759.JPG (238KB - 48 downloads) DSCN9760.JPG (223KB - 51 downloads) | ||
finsruskw |
| ||
Expert Posts: 2289 Location: Eastern Iowa | Still available Price drop to $150 Somebody please come and get them! | ||
STOCKHEMI |
| ||
Veteran Posts: 148 | Hi just wondered if you had any other 57 parts as a job lot thanks | ||
finsruskw |
| ||
Expert Posts: 2289 Location: Eastern Iowa | Have a few headlamp trim pieces and the pot metal buckets that they surround. Front and rear bumper cores suitable for replating. A decent rt front door for a 2 door hardtop A few odds and ends of side trim you would have to identify. Intake manifold for a single 4 bbl carb, 392 CID Pair of rocker panel repair panels for a 2 door, (light surface rust) Looking for anything in particular? Edited by finsruskw 2022-11-30 7:21 PM | ||
STOCKHEMI |
| ||
Veteran Posts: 148 | Hi would be interested some of these parts Have you any project cars etc mopar for sale? I do need rear light lens and hoop bracket support ? 331 heads / 392 etc rods poss more These are all to ship in a package or vehicle ? Maybe | ||
finsruskw |
| ||
Expert Posts: 2289 Location: Eastern Iowa | Hood bracket support?? Can you elaborate a bit on that? Maty have a rear tail lamp ass'y, not sure of the lens though If I do, it would be a Glo-Brite aftermarket piece | ||
STOCKHEMI |
| ||
Veteran Posts: 148 | Rockers panels intrested Do you still have the fenders ? Door if skin is not to bad Headlight parts And the trim ,do you what car they have come from ? Have you any 57 desoto engine parts ? Or W H Y ! Thanks Edited by STOCKHEMI 2022-12-05 1:31 PM | ||
finsruskw |
| ||
Expert Posts: 2289 Location: Eastern Iowa | Stuff is all from 57-58 New Yorkers The door is from a 300D. Also have power seat unit, no seats though. | ||
STOCKHEMI |
| ||
Veteran Posts: 148 | IS the door decent on the bottom and the skin outside ? And is t bare with no internals or glass ,price thanks Can you give me prices on what you have ,any possibility of shipping ? Thanks | ||
finsruskw |
| ||
Expert Posts: 2289 Location: Eastern Iowa | First off, where are you located. Shipping will not be cheap for something like this. It will almost have to be in some kind of crate for protection. I will get you some pictures today. Thanks for the inquiry | ||
finsruskw |
| ||
Expert Posts: 2289 Location: Eastern Iowa | Got a ton of pictures for you Get me an e-mail address and I'll get them on the way Too big a PITA to have to fool around resizing them all for this site Door glass is broken but the PW operating system is in place and it works. Vent widow frame and support is pitted but the glass is OK Door handle is gone, no trim panels. Hinges are there if you need them. Weight as is will be near 70 pounds, unless you just want a bare door, removing these parts would lighten it considerably. Adding s crate of some sort will add weight as well. No damage to the door proper but there are a few pin point rust spots on the outside. Most of the factory undercoating is in place yet $300 for the door as is Plus crating & freight FOB 52041, Eastern Iowa Edited by finsruskw 2022-12-11 2:18 PM | ||
finsruskw |
| ||
Expert Posts: 2289 Location: Eastern Iowa | This item, 58 300D door, has been SOLD!! Edited by finsruskw 2022-12-12 7:38 AM | ||
Jump to page : 1 Now viewing page 1 [50 messages per page] |
Search this forum Printer friendly version E-mail a link to this thread |
(Delete all cookies set by this site) | |