The Forward Look Network
The Forward Look Network
Search | Statistics | User Listing Forums | Chat | eBay | Calendars | Albums | Skins | Language
You are logged in as a guest. ( logon | register )

Rear axel swap
Jump to page : 1
Now viewing page 1 [50 messages per page]
View previous thread :: View next thread
   Forward Look Technical Discussions -> Transmission and Rear AxleMessage format
 
jeff b
Posted 2023-03-18 11:43 PM (#628348)
Subject: Rear axel swap


Veteran

Posts: 113
100
Hello,
Has anyone put a B body rear end from a 1964 Plymouth into a 1958 Plymouth? Any issues
Thanks
Top of the page Bottom of the page
Shep
Posted 2023-03-19 11:08 AM (#628355 - in reply to #628348)
Subject: Re: Rear axel swap



Expert

Posts: 3393
20001000100100100252525
Location: Chestertown, NY ( near Lake George)
65 is a better choice, you have the easily removable drums and slightly stronger axles. Not sure about width, easy to check that online. Also make sure it comes out of an 8 cylinder car.

Edited by Shep 2023-03-19 11:10 AM
Top of the page Bottom of the page
Powerflite
Posted 2023-03-19 12:15 PM (#628358 - in reply to #628348)
Subject: Re: Rear axel swap



Expert 5K+

Posts: 9605
500020002000500100
Location: So. Cal
The B-body axle is a little narrower, so if you use that, you will need deeper dish wheels. Otherwise, use the '65-'69 C-body axle instead.
Top of the page Bottom of the page
jeff b
Posted 2023-03-19 12:38 PM (#628361 - in reply to #628348)
Subject: Re: Rear axel swap


Veteran

Posts: 113
100
Ok thanks really appreciate it. I was concerned about pinion angle as well, and driveshaft compatibility. Look like I need to find a C Body rear
Top of the page Bottom of the page
Shep
Posted 2023-03-21 8:47 AM (#628406 - in reply to #628361)
Subject: Re: Rear axel swap



Expert

Posts: 3393
20001000100100100252525
Location: Chestertown, NY ( near Lake George)
Pinion angle set when the spring perches are welded in or moved as necessary.
Top of the page Bottom of the page
57chizler
Posted 2023-03-21 2:07 PM (#628414 - in reply to #628348)
Subject: RE: Rear axel swap



Expert

Posts: 3768
200010005001001002525
Location: NorCal
The '65-'67 C-body rear end is a better choice, the pinion angle is correct and the spring perch spacing is close enough for a drop-in...no welding required.
Top of the page Bottom of the page
chstrumpetdude
Posted 2023-03-21 4:58 PM (#628421 - in reply to #628348)
Subject: Re: Rear axel swap


Regular

Posts: 57
2525
Location: Springfield, MO
I also understand that certain E-body is acceptable, but the pinion angle is off by 3 degrees. I could not find a C-body for my car, but did find a cheap 71 E-body
Top of the page Bottom of the page
Shep
Posted 2023-03-21 5:51 PM (#628422 - in reply to #628421)
Subject: Re: Rear axel swap



Expert

Posts: 3393
20001000100100100252525
Location: Chestertown, NY ( near Lake George)
Pinion angle is dependent on the height of the front suspension so there are still variables in this issue, slip yoke driveshaft s have a different procedure then the old style shaft. Until the car is at ride hgt., it is impossible to get an accurate measurement on the final pinion angle, if off at this point, wedge shims can correct it.

Edited by Shep 2023-03-21 9:39 PM
Top of the page Bottom of the page
matador440
Posted 2023-03-24 5:03 PM (#628491 - in reply to #628422)
Subject: Re: Rear axel swap



Elite Veteran

Posts: 690
500100252525
Location: BELTSVILLE, MARYLAND 20705
I have used E body rears about 15 times they work great . They bolt right in. You can get a 3 degree shim off ebay and install it when you are installing the rear. With the c body rear you have to re weld and move the spring perches on the housing. With the ebody you can also move your emergency brake cable to the rear wheels ( MUCH SAFER). You can also use your original wheels with this conversion. OVER ALL ITS A NICE AND SAFER IMPROVEMENT. With this e body you now you can use any gear ratio 3rd member and not have to pull the drums with a puller-- just slide off the drums .
Top of the page Bottom of the page
Powerflite
Posted 2023-03-24 6:10 PM (#628495 - in reply to #628348)
Subject: Re: Rear axel swap



Expert 5K+

Posts: 9605
500020002000500100
Location: So. Cal
You realize that the only difference between the '65-'69 Cbody and '70-'74 Ebody rears is the pinion angle. That's it - along with maybe different length e-brake cables. All the things you mention are the same.
Top of the page Bottom of the page
57plymouth
Posted 2023-03-25 7:43 AM (#628511 - in reply to #628495)
Subject: Re: Rear axel swap



Expert

Posts: 3577
20001000500252525
Location: Blythewood, SC
Powerflite - 2023-03-24 6:10 PM

You realize that the only difference between the '65-'69 Cbody and '70-'74 Ebody rears is the pinion angle. That's it - along with maybe different length e-brake cables. All the things you mention are the same.


Plus, there were more C bodies built and less E bodies. The muscle car builders would prefer the E body stuff so the C body axle would be more common and cheaper.
Top of the page Bottom of the page
Apollo 61
Posted 2023-03-25 8:48 PM (#628534 - in reply to #628348)
Subject: Re: Rear axel swap



Elite Veteran

Posts: 765
5001001002525
How does a 70 C body rear end work in?
Top of the page Bottom of the page
Powerflite
Posted 2023-03-25 10:46 PM (#628537 - in reply to #628348)
Subject: Re: Rear axel swap



Expert 5K+

Posts: 9605
500020002000500100
Location: So. Cal
1970 C-body rears became much wider.



(8_3-4Axles.jpg)



Attachments
----------------
Attachments 8_3-4Axles.jpg (140KB - 61 downloads)
Top of the page Bottom of the page
57chizler
Posted 2023-03-26 3:31 PM (#628554 - in reply to #628495)
Subject: Re: Rear axel swap



Expert

Posts: 3768
200010005001001002525
Location: NorCal
Powerflite - 2023-03-24 3:10 PM

You realize that the only difference between the '65-'69 Cbody and '70-'74 Ebody rears is the pinion angle.


And the location of the vent hole, not a big issue but it affects the brake hose length.

'70-'74 E-body housing: Vent bolt location: 11.25" from center of housing

'65-'69 C-body housing: Vent bolt location: 7.75" from center of housing
Top of the page Bottom of the page
Powerflite
Posted 2023-03-27 11:46 AM (#628570 - in reply to #628348)
Subject: Re: Rear axel swap



Expert 5K+

Posts: 9605
500020002000500100
Location: So. Cal
Thanks for that info Chizler. That provides a convenient way to figure out which axle you really have. Do you have a suggestion for a brake hose to use with the C-body housing? I have always resorted to moving the body mount to get it closer. There is also the '65-'70 A100 van which can be confused between them. Do you know of any differences between that one and the others?
Top of the page Bottom of the page
57chizler
Posted 2023-03-27 2:17 PM (#628577 - in reply to #628570)
Subject: Re: Rear axel swap



Expert

Posts: 3768
200010005001001002525
Location: NorCal


When I swapped a C-body into my '57 I just measured the required length for the hose to reach the fitting and clear the non-stock exhaust and found a hose with the needed end fittings.

Don't know much about the A-100 other than the width but I imagine the spring pad spacing is different. Don't know where the breather is located.
-----
Despite the cost of living, have you noticed how it remains so popular?



(CIMG0624 (Small).JPG)



Attachments
----------------
Attachments CIMG0624 (Small).JPG (144KB - 54 downloads)
Top of the page Bottom of the page
Jump to page : 1
Now viewing page 1 [50 messages per page]
Jump to forum :
Search this forum
Printer friendly version
E-mail a link to this thread

* * * This site contains affiliate links for which we may be compensated * * *


(Delete all cookies set by this site)