Re: IML: signal sw. removal 67 imperial
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: IML: signal sw. removal 67 imperial



Great pictures. That is a great idea to keep the switch fresh. now, I hope it flashes better for you and doesn't drag everything down when your stopped.

Jason Beinbrech, Riverside CA
67 le baron
67 crown

On 2/28/07, Ken Lang <imperialken@xxxxxxxxx> wrote:
Chris,

I just replaced the turn signal switch in my 67 (and 68).  During the
process I managed to take a few photos and typed up a little blurb about how
I did it.  You can check it out at:

http://www.imperialclub.com/Yr/1967/67TurnSignal/index.htm

The outer column sleeve (officially known as the Tilt Actuator Cover) is
removed using a slide-hammer type of tool.  It is held in place by virtue of
a very snug fit.  I had to make my own tool from an existing slide-hammer.

Looking through the 67 FSM I can't find any picture or reference to it.  But
the 68 FSM has good detail of the procedure.  Contact me off list if you
want me to scan a couple of these pages and sent them to you.

Ken
67 Crown 4 Dr Ht
68 LeBaron 4 Dr Ht


-----Original Message-----
From: mailing-list-owner@xxxxxxxxxxxxxxxx
[mailto:mailing-list-owner@xxxxxxxxxxxxxxxx] On Behalf Of Chris Strohmeyer
Sent: Wednesday, February 28, 2007 6:14 PM
To: mailing-list@xxxxxxxxxxxxxxxx
Subject: IML: signal sw. removal 67 imperial

Below is what I read on the Imp club site, but he doesn't mention HOW this
outer column sleeve is physically attached. Does it drive  off? Is it just a

press fit? Dick Benjemin mentions to bend the switch to get it out without
removing the sleeve, but at the price of these switches I don't want to take

the chance of breaking the existing one which I may be able to be repaired.
Mine has the red color and has no broken parts but the main rivet that holds

it together might be the problem. I don't really need to get it all the way
out, I just need it outside the sleeve to see what's keeping it from staying

engaged when the signal lever is depressed. It's possible that whomever
replaced this switch might have damaged it forcing it in there.
So how do I get this sleeve off and what is this special tool to remove it?

Thx,
Chris Strohmeyer
67 Imperial Convertible (read below)


I presume getting that tubular sleeve off is what is stopping you cold. One
way to get it off is to use a piece of hardwood or a nylon drift (available
at gun shops, looks like a glue stick) to tap it loose from the tilt opening

(the lever screws out, just twist it!) and then work a screwdriver into the
gap at the base of the column. My car would have none of that, that !@#$
sleeve was TIGHT! What I wound up doing was to pry the lip up with a
scgewdriver (in an attempt to loosen the sleeve, no deal!) I then attached a

pair of vise-grips to two sides of the pried up lip and alternately hammered

on the vise-grips to get the !@#$ off! Once off I measured up to the mangled

part and carefully wrapped masking tape around the outside, cut off the
mangled 3/8 inch or so and filed down to the edge of the tape. The tape
protected the paint on the sleeve and if someone didn't know the sleeve had
a lip, you can't tell it has ever been altered! It's all hidden by the wheel

anyway. Best of all, if the switch ever needs replacing again, the sheeve
won't have to be touched!



-----------------  http://www.imperialclub.com  -----------------
This message was sent to you by the Imperial Mailing List. Please
reply to mailing-list@xxxxxxxxxxxxxxxx and your response will be
shared with everyone. Private messages (and attachments) for the
Administrators should be sent to webmaster@xxxxxxxxxxxxxxxx
To UN-SUBSCRIBE, go to http://imperialclub.com/unsubscribe.htm



-----------------   http://www.imperialclub.com  -----------------
This message was sent to you by the Imperial Mailing List. Please
reply to mailing-list@xxxxxxxxxxxxxxxx and your response will be
shared with everyone. Private messages (and attachments) for the
Administrators should be sent to webmaster@xxxxxxxxxxxxxxxx
To UN-SUBSCRIBE, go to http://imperialclub.com/unsubscribe.htm




Home Back to the Home of the Forward Look Network


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.