RE: [Chrysler300] Astrodome-Speedometer
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

RE: [Chrysler300] Astrodome-Speedometer



I have the same problem with our F.

Been there since we put it on the road in ?84 or so.

Will work fine up to 50-60 or so then sticks.

If Ya mash on it ater that to around 80 it will jump over whatever it?s
hanging up on and work fine

till you slow back down and then hang up again till you get down to 35 or
so.

I usually drive by the tach, seems to be legal at around 2850 rpm?s

 

Dave Schwandt

 

From: Chrysler300@xxxxxxxxxxxxxxx [mailto:Chrysler300@xxxxxxxxxxxxxxx] On
Behalf Of 'John Grady' jkg@xxxxxxxxxxxxxxxxx [Chrysler300]
Sent: Thursday, July 31, 2014 4:04 PM
To: 'GERALD OLSON'
Cc: 'list server'
Subject: RE: [Chrysler300] Astrodome-Speedometer

 






There is little hair spring that returns it, and if stuck , chances are
needle is bent and touching or somehow it jumped out of tiny journals it
(needle)turns in.   I do not think anything can go wrong inside,  drive
wise, as the part that spins magnet to move needle is directly driven by and
mounted on cable inlet ---and odometer drives off that ,so it is spinning,
if odometer moves, but needle is stuck. Might be easy,  might be a bear. I
have gotten into these and if you bend or mess around with bending either
the spinning part or magnet, or the spring, it ends up 10-15 mph off after
all that effort . Bending is related to fixing obvious problem of the parts
hitting or scraping .

 

It works by ?eddy current? which is spinning magnet induces a current into
the aluminum cup , makes a torque proportional to speed, which then fights
the multiturn hairspring harder and harder as you speed up; the exact gap
--supposed to be between them ---impacts the torque ; bending wrecks all
that. 

 

Most common problem seems to be wear in bearing right at end of cable..often
no lube there , for years dried out (a few drops of oil are good?there is
felt thing on some of them to hold oil)--- when that wear happens what is
supposed to spin and run true does not do that; cup like thing starts
wobbling a little and one spinning cup - like part touches the other needle
cup part ,so needle jumps up and then falls back, or wiggles at steady
speeds; if violent enough or piece of dirt, can hurt needle,--- And its
bearing/mount ..might have happened. Usually shiny place and history of
needle jumping around, or flying up to 150. .

 

Wish I could say ?do this? but best way , after many wasted hours, is
another one,  or send to specialist. Bob?s speedometer comes to mind, think
I used that once , in Hemmings, but it was healthy bucks to rebuild it, and
very hard to do yourself, if not impossible due to specialized parts,
riveted/die cast swaged together. If you bend that super fragile hair spring
you are done for,  as far as accuracy?that is what sets reading per RPM . So
find a used one, hopefully  with low miles? On the other hand it might have
fallen out of bearing and with tweezers you get it back..but not easy.
Nothing to lose by looking. Tang you see on hair spring mount is to set
zero, and calibration should fall out of that. It may literally be just
touching dial  /stuck. Ok to bend needle slightly to fix that . 

 

A drop of oil on odo gear drive places is good too, while in there ..it can
jam and then strip nylon drive  teeth. (other issue in there) ; you hear
faint click, click click and odo does not move, very soon no teeth left.
Cannot be fixed, without speedo parts, although I put a washer under one end
moved it over to engage remains of teeth, got one going, after freeing
number drum  . 

 

I have 60 Dodge with stuck needle..that Speedo needle is about 6? long runs
in a narrow slot and scrapes it, one side or other --went through two of
them--- still does not work and cannot find  good used one , must have 15
hours of in it, no cigar...looseness in needle mounts makes it not stay
centered in slot . Plus hours to get these in and out . 

 

I believe , in trying to fix this a while back , I found out somewhere there
is a standard RPM for MPH, want to say 60MPH is 1000 RPM  on cable , but do
not take that to bank?got the impression all car speedos use that. I used
speed on ½? drill rated 950 RPM to set it close, but all in all came out
poorly/erratic ?but it does go up.  . I used wood like a  toothpick in drill
to drive it held in vise. Could compare to good one that way too. 

 

All in all a cheaply made,  really crappy thing; 100k miles and ? 5 years it
is hurting/worn out; just $0 .50 more could have beefed up input bearing
length a lot, would last forever, never wobble. Depends if yours got oiled
at assembly , too. 

 

Good luck,

 

john

 

From: Chrysler300@xxxxxxxxxxxxxxx [mailto:Chrysler300@xxxxxxxxxxxxxxx] On
Behalf Of GERALD OLSON olson77@xxxxxxxxxxxxx [Chrysler300]
Sent: Thursday, July 31, 2014 3:38 PM
To: Chrysler300@xxxxxxxxxxxxxxx
Subject: [Chrysler300] Astrodome-Speedometer

 





Anyone out there have any suggestions when the odometer works fine and the
speedometer is stuck at 50 MPH weather we're doing 100 MPH or 0 MPH. No
wiggle, no dance, no movement what so ever! Thanks for any input and or
cure, Jerry





 










[Non-text portions of this message have been removed]



------------------------------------
Posted by: "David Schwandt" <finsruskw@xxxxxxxxxxxxxxx>
------------------------------------

To send a message to this group, send an email to:
Chrysler300@xxxxxxxxxxxxxxx

To unsubscribe from this group, send an email to bob@xxxxxxxxxxxxx or
go to http://autos.groups.yahoo.com/group/Chrysler300/join and select the "Leave Group" button

For list server instructions, go to http://www.chrysler300club.com/yahoolist/inst.htm

For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
------------------------------------

Yahoo Groups Links

<*> To visit your group on the web, go to:
    http://groups.yahoo.com/group/Chrysler300/

<*> Your email settings:
    Individual Email | Traditional

<*> To change settings online go to:
    http://groups.yahoo.com/group/Chrysler300/join
    (Yahoo! ID required)

<*> To change settings via email:
    Chrysler300-digest@xxxxxxxxxxxxxxx 
    Chrysler300-fullfeatured@xxxxxxxxxxxxxxx

<*> To unsubscribe from this group, send an email to:
    Chrysler300-unsubscribe@xxxxxxxxxxxxxxx

<*> Your use of Yahoo Groups is subject to:
    https://info.yahoo.com/legal/us/yahoo/utos/terms/



Home Back to the Home of the Forward Look Network Archive Sitemap


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.