AW: [Chrysler300] Steering wheel repair
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

AW: [Chrysler300] Steering wheel repair





Dear all,

 

Thanks for the lively discussion and the valuable contact of Dennis, my steering wheel also needs complete overhaul.

Kai from Germany

 

Dr. Kai Rentmeister

Tierarzt, DiplECVN

Tierärztliche Praxis für Neurologie

Sandäcker 7

97337 Dettelbach

09324 - 9787630 Tel

09324 - 9787635 Fax

info@tierneurologie

www.tierneurologie.de

 

-----Ursprüngliche Nachricht-----
Von: Chrysler300@xxxxxxxxxxxxxxx [mailto:Chrysler300@xxxxxxxxxxxxxxx] Im Auftrag von 'Fern Rivard' crc@xxxxxxxxxxxx [Chrysler300]
Gesendet: Mittwoch, 21. September 2016 20:58
An: Richard Osborne; Val Jeffers
Cc: Michael Moore; Mark Souders; ssbeard2015@xxxxxxxxxxx; chrysler300@xxxxxxxxxxxxxxx
Betreff: Re: [Chrysler300] Steering wheel repair
Wichtigkeit: Hoch

 

 

I had the wheel on our 300H convertible restored by Dennis about 8 years ago and it still looks like new.

My recollection is that it cost around $1200 to get it down but I agree with Richard that I would use him again as his workmanship is awesome.  We have real cold winters out here in BC and no cracks, etc.

Fern

 

 

Sent: Wednesday, September 21, 2016 11:53 AM

Subject: Re: [Chrysler300] Steering wheel repair

 

 

Hi Val,

 

I had the wheel for my G done by Dennis Crooks somewhere around 10 years ago. It still looks amazing.

 

Keep in mind my car has been in the desert (115F) and sits in a non-climate controlled garage in central Ohio during the winter months. The car has also spent time in the sun and the wheel still looks the same as the day I got it back. I would use Dennis again in a heartbeat, even if it meant having to save up for the extra cost. It’s my opinion that the dash in a G (or F) is highlighted by the clear wheel and I am proud of the way mine looks.

 

My 2 cents.

 

Richard Osborne

 

 

 

On Sep 21, 2016, at 8:51 AM, Val Jeffers edward1108@xxxxxxxxx [Chrysler300] <Chrysler300-noreply@xxxxxxxxxxxxxxx> wrote:

 

Speaking of steering wheel restoration, who is the best ? My G's wheel is in need.

 

                         Thanks,

 

                         Val Jeffers


Sent from Yahoo Mail for iPhone

On Wednesday, September 21, 2016, 8:46 AM, Michael Moore mmoore8425@xxxxxxx [Chrysler300] <Chrysler300-noreply@xxxxxxxxxxxxxxx> wrote:

 

Hey Mark,

I did the same thing with my 300H after I had the clear part recast. It looked great, in fact I had my spare done also. My PV-7 cracked in a couple of places several years later, so I put my spare on, and fixed the cracked one.Theone on now has held up for 20 years. Even if the PV7 cracks every 5 years, it’s not that tough to patch and repaint.

Mike Moore

300H

 

On Sep 21, 2016, at 5:32 AM, Mark Souders MRS954@xxxxxxx [Chrysler300] <Chrysler300-noreply@xxxxxxxxxxxxxxx> wrote:

 

 

Steve,

I was in the same position when I built my 300H. I repaired a Newport wheel using a two-part epoxy. JB Weld works but it is too viscous and will run out of the cracks before it is set up. I used PC7. It's a two part epoxy, exactly like JB Weld, but is a thicker paste (if you insist on using JB Weld, you will wish you bought the PC7). PC7 comes in 2 cans taped together, from your local hardware store. Clean and prepare the wheel with a cleaner and some light sand paper. Make sure there's no dirt or scale in the cracks. Mix up the epoxy and push it into all the cracks. They tell you to use a putty knife, but I just used my wet fingers. Oh, and it's very important to make sure your fingers are wet. Have a cup or bowl of water with you and keep your fingers wet or else the epoxy will stick to your fingers for about two weeks. So with wet fingers, you can form and shape the epoxy to the contour of the wheel. With wet fingers, smooth out the epoxy to match the form o f the wheel. Let the epoxy set up over night. Next day, sand it smooth and paint the wheel the desired color. You will be so happy with the outcome, you may never spend the $1500 for a restored wheel.

 

Happy Moparing,

Mark

 

 

 

 

-----Original Message-----
From: Sandy Beard ssbeard2015@xxxxxxxxxxx [Chrysler300] <Chrysler300-noreply@xxxxxxxxxxxxxxx>
To: chrysler300 <chrysler300@xxxxxxxxxxxxxxx>
Sent: Wed, Sep 21, 2016 7:30 am
Subject: [Chrysler300] Steering wheel repair

 

Good morning 300 ites. For those going to the fall meets east and west, drive safe and have 300 fun.

Need to do some repair on my F steering wheel. The wheel is cracked  in several places. can't afford a new one at this time( $1500 ouch). Anyone have some ideas/ suggestions on temporary repair that looks good. Also looking to know  what engine a 4 barrel intake manifold dated 1958 might have come off of.  looks smaller then a big block manifold.

Thanks

Steve Beard

300 F

Delaware, Ohio

 

 

 

 

 




Avast logo

Diese E-Mail wurde von Avast Antivirus-Software auf Viren geprüft.
www.avast.com




__._,_.___

Posted by: "Dr. Kai Rentmeister" <kai.vet@xxxxxx>


To send a message to this group, send an email to:
Chrysler300@xxxxxxxxxxxxxxx

To unsubscribe from this group, send an email to bob@xxxxxxxxxxxxx or
go to https://groups.yahoo.com/neo/groups/all/manage/edit

For list server instructions, go to http://www.chrysler300club.com/yahoolist/inst.htm

For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang





__,_._,___


Home Back to the Home of the Forward Look Network Archive Sitemap


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.