RE: [Chrysler300] Removal of 55 year old undercoating
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

RE: [Chrysler300] Removal of 55 year old undercoating





 

 

From: John Grady [mailto:jkg@xxxxxxxxxxxxxxxxx]
Sent: Friday, January 13, 2017 9:20 AM
To: Noel Hastalis
Cc: Carlton Schroeder' schroe99@xxxxxxxxxxxx [Chrysler300]; Chrysler300@xxxxxxxxxxxxxxx; Carlton Schroeder
Subject: Re: [Chrysler300] Removal of 55 year old undercoating

 

Agree with Noel we have used the real truck bed liner . Had one problem, any oil even a minuscule amount destroys the bond , and it will come off in thin sheets or patches.. near trans for us.. there are probably directions for thorough prep that need to be followed. I only mention this as kerosene will leave an oily film , could be a disaster . Need some kind of solvent even Keri maybe but followed by thorough hot pressure wash with detergent, my.02 ----first  , before you spray . Results are excellent , avoids removing old except where loose .  

Sent from my iPhone


On Jan 12, 2017, at 11:47 PM, Noel Hastalis cpaviper@xxxxxxxxxxx [Chrysler300] <Chrysler300-noreply@xxxxxxxxxxxxxxx> wrote:




Hello Carlton,

 

I don't know how far along you are in scraping the undercoating from your fenderwells, and how bad the integrity is of the undercoating. John Begian put me onto using Truck Bed Coating - I've used the Dupli-Color aerosol cans, available at any Napa, etc. store. The product name is TR250 Black Truck Bed Coating. It's easy to tape off the surfaces you don't want sprayed, and spray over the factory-applied wheel well undercoating. It retains the 'rough' factory spray-on finish, and looks great. You'll need at least a half-dozen spray cans, if going this route.

 

Good Luck!

Noel

On January 12, 2017 at 9:54 PM "'Carlton Schroeder' schroe99@xxxxxxxxxxxx [Chrysler300]" <Chrysler300-noreply@xxxxxxxxxxxxxxx> wrote:

 

Hello from the very snowy and very cold Northwood’s of Wisconsin,

(and Eagle River, home of the World Championship Snowmobile Derby)

 

I am currently in the middle of the very unpleasant job of removing old and hard but very well attached old undercoating on my 300H. The bottom of the car is complete (sand blasted and painted although there was not much undercoating left) so it is only the inner and outer fenders (with thicker undercoating) that I need to clean of undercoating.  The fellow who will be painting is reluctant to try to sand blast it off so I am using PB Blaster, Liquid Wrench, and kerosene to soften and then scrap off the undercoating.    I’m working in about 50F temp in my garage so I could probably warm up (kerosene tube heater) the fenders further if that would help.  Or if there are stronger solvents that don’t evaporate too quickly, that would probably help too.

I’ll appreciate all suggestions.

Thanks,

Carlton Schroeder    


 






__._,_.___

Posted by: "John Grady" <jkg@xxxxxxxxxxxxxxxxx>


To send a message to this group, send an email to:
Chrysler300@xxxxxxxxxxxxxxx

To unsubscribe from this group, send an email to bob@xxxxxxxxxxxxx or
go to https://groups.yahoo.com/neo/groups/all/manage/edit

For list server instructions, go to http://www.chrysler300club.com/yahoolist/inst.htm

For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang





__,_._,___


Home Back to the Home of the Forward Look Network Archive Sitemap


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.