Re: [Chrysler300] Parade issues
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [Chrysler300] Parade issues





Not a permanent fix, but this is how I fixed one of my Rods too many years ago.
Too big an engine and too small a radiator, had me overheating at highway speeds.
I opened the hood and took 2 small rocks on the side of the road, opened the hood and placed the rocks on the cowl. Closed the hood with them under the rear of the hood which jacked the springs up, leaving a nice gap at the back of the hood.
Gave me great airflow under the hood.
I had no more heat problems with it until I replaced the small rad. with a 4 tube one to match the 409c.i. engine.
Your degrees may vary...
Ray

On Sun, Jun 18, 2017 at 2:36 PM, John Grady jkg@xxxxxxxxxxxxxxxxx [Chrysler300] <Chrysler300-noreply@xxxxxxxxxxxxxxx> wrote:
 

Hi if if fluid in lines expands it simply backs into master cylinder on non ram j/k drum brakes --even with a residual pressure valve , it cannot hold the brakes to drum ? is there a residual pressure valve in these non ram stock ? Also issue of hydrovac on ram cars . If a master "for a 300"-- the common one --w residual pressure is used as the master drive to hydrovac it will actuate the hydrovac by itself leading to locking . Probably caused by expansion in connecting line. That might be happening if this is a ram car. I believe with hydrovac you have to have a special no residual valve master or remove it. Same thing happens on non ram when you take foot off brakes. It runs back in, non ram. If it locks up on touching that has to be a booster engagement problem, as there is simply no way to generate enough psi to lock brakes unless booster is active. Over active .
I agree given two instances --high temp must cause it , but somehow by impacting booster or on non ram the trigger adjustment. Perhaps heat impacts an adjustment that is very critical and not set correctly ?? as I understand it they say in FSM not to ever touch the trigger adjustment. To many that is a blank invite to go right at it . As by definition, they know far more than FSM and guys who designed it . If ram car, might have the wrong master .
Not running well on hot days w j manifolds almost says too much carb heat getting up there . On highway even more gas flow under carb would still keep carb too hot . On hot day . George used to restrict that flow , thin metal plate in elbow , Don Cole did too . Don had a very fast K , blocked heat . He might chime in .

Sent from my iPhone



> On Jun 18, 2017, at 2:14 PM, 'David Schwandt' finsruskw@xxxxxxxxxxxxxxx [Chrysler300] <Chrysler300-noreply@yahoogroups.com> wrote:
>
> Simple....Too much under hood heat, heating the brake system DOWNSTREAM from
> the M/C, expanding the fluid in the lines, just enough to have the same
> effect as riding the brakes. Expect it to happen again even w/the new parts.
> Add an electric fan to help move the hot air and/or crack the hood open
> letting it catch on the 2nd catch
> Rams by any chance w/ stock headers???
> I have the same issue w/my F (had J/K headers) in high heat conditions.
> Won't run worth a crap when temps are in the 90's, even at highway speeds.
> The trip home from McCungie was a nightmare 2 years ago.
> Good luck!!
> Dave Schwandt
>
>
> -----Original Message-----
> From: Chrysler300@xxxxxxxxxxxxxxx [mailto:Chrysler300@yahoogroups.com] On
> Behalf Of samacisaac@xxxxxxxxx [Chrysler300]
> Sent: Sunday, June 11, 2017 3:08 PM
> To: Chrysler300@xxxxxxxxxxxxxxx
> Subject: [Chrysler300] Parade issues
>
> Drove my 64 300 in a parade yesterday, aftermarket temp gauge went off the
> scale but wasn't puking water or boiling over, main concern was 1/2 way thru
> had brake issues, started acting like brakes were dragging, although I never
> smelled them (tranny tightening up maybe?) and lost the power brakes, pedal
> got rock hard and when brake was applied she wanted to launch you thru the
> windshield. (New master cylinder and booster, less than 150 miles on them)
> Today she's fine. Any ideas?
>
> Sent from my iPhone
>
>
> ------------------------------------
> Posted by: samacisaac@xxxxxxxxx
> ------------------------------------
>
> To send a message to this group, send an email to:
> Chrysler300@xxxxxxxxxxxxxxx
>
> To unsubscribe from this group, send an email to bob@xxxxxxxxxxxxx or go to
> https://groups.yahoo.com/neo/groups/all/manage/edit
>
> For list server instructions, go to
> http://www.chrysler300club.com/yahoolist/inst.htm
>
> For archives go to
> http://www.forwardlook.net/300-archive/search.htm#querylang
> ------------------------------------
>
> Yahoo Groups Links
>
>
>
>
>
>
> ------------------------------------
> Posted by: "David Schwandt" <finsruskw@xxxxxxxxxxxxxxx>
> ------------------------------------
>
> To send a message to this group, send an email to:
> Chrysler300@xxxxxxxxxxxxxxx
>
> To unsubscribe from this group, send an email to bob@xxxxxxxxxxxxx or
> go to https://groups.yahoo.com/neo/groups/all/manage/edit
>
> For list server instructions, go to http://www.chrysler300club.com/yahoolist/inst.htm
>
> For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
> ------------------------------------
>
> Yahoo Groups Links
>
>
>




--
Ray Jones. Y'all come on down an see us. Ya hear?


__._,_.___

Posted by: Ray Jones <1970hurst@xxxxxxxxx>


To send a message to this group, send an email to:
Chrysler300@xxxxxxxxxxxxxxx

To unsubscribe from this group, send an email to bob@xxxxxxxxxxxxx or
go to https://groups.yahoo.com/neo/groups/all/manage/edit

For list server instructions, go to http://www.chrysler300club.com/yahoolist/inst.htm

For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang




Visit Your Group
Yahoo! Groups
PrivacyUnsubscribeTerms of Use

__,_._,___


Home Back to the Home of the Forward Look Network Archive Sitemap


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.