Re: {Chrysler 300} 64 K fuel sender and gauge
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: {Chrysler 300} 64 K fuel sender and gauge



Thanks again, John for posting this info again.  I remembered it from our FCBO forum, but I lost track of it.

Just now ordered the whole shebang for my '66 300.

Rip 

On Monday, February 14, 2022, 12:14:30 PM EST, 'John W Sager' via Chrysler 300 Club International <chrysler-300-club-international@xxxxxxxxxxxxxxxx> wrote:


I've used a Meter Match to correct the sender resistance to the gauge. This is a great product and I am very happy with the results.  Pretty simple to install too. A friend has one in his car too. Same good results. 





On Monday, February 14, 2022, 11:47:58 AM EST, John Grady <jkg@xxxxxxxxxxxxxxxxx> wrote:


Hi,
none of the “new “ senders  sold by all the vendors are calibrated correctly for our mopars . I have 5-6 in various cars ( little choice if old one is toast )  they do not track right . All the same chinese junk . Not one works right . Not just several 300 , —a Dart and two dodge trucks too . The rate of change of ohms or float travel ( arm geometry ) or both is wrong . If you look at the stock resistor winding ,  the resistor is non linear it changes width as wound on the form in the tank sensor in an engineered way to drive the probably non linear gauge to track the gas level . That non linearity probably varies with tank shape.  Slanted bottom for instance . 

 = save the old one ...... job 1 

you cannot fix that tracking problem with resistors either . 

Two other possibilities , figure out E on gage vs arm out of tank and bend arm E so E end is near correct in tank (what you really care about ) , when float is down ,easiest when the tank is out of car , —- F accuracy really does not matter . Resistors will impact F end only , essentially . If you try to correct E with resistor to make it read lower gauge will not go full travel , as it can no longer get to 10 ohms. (F) 
I have tried to put yellow stickies in each car ( sad ) telling me the story . You forget . 

When Dart reads E it still takes 11 gallons . So you drive on E and watch odometer , leading to running out .  It Goes from E to F in just last 8 gallons . Others not as bad but you get it . yet sender is correct 10-90 ohms approx .  
The brass float tank on an old one can be fixed by adapting ford parts . Was 18$ for two new Ford brass floats a while back . maybe you can save the old resistor part by careful cleaning rust out with Q tip and wooden toothpick inside the little box . Do NOT bend little arm to “make  better contact “ it will rip up the resistor wire in a month . been there . resistor wire is very fragile why no metal tools .  
 If winding wire is already ripped or loose it is junk . 

Last , while chasing this , Tanks Inc sells a really nice universal mechanically adjustable sensor , available  
with mopar 10-90 ohm range , designed for their tanks ,  but best part is it has a spectacular instruction exactly how to measure to set it up , the float travel , arm length , centering the pivot in the tank depth etc . Those parts come with it. 
This looks to me to be rather easily adaptable to our stock inlet fitting and the stock resistor support or mount arm . I have not had the time — although I bought one . 
Maybe someone else does it — with a tank out of car . Connect that tank on bench to the car with two jumper wires . Document it . 
The other post about ground is very true . You can solder a wire , 14 ga stranded building wire to the outlet pipe below outlet hose . clean thoroughly till shiny . Run to frame .    Mostly though , bad ground shows as an E reading there all the time or comes and goes , not an error in reading . 
Hope this helps . Frustrating thing . 
John g 
ps don’t mess with dash gauge over this . goes nowhere but trouble . 
PPS , new G tanks are listed —but not F ! It turns out the difference  is length of filler pipe . It works ok 
Sent from my iPhone not by choice 

On 14 Feb 2022, at 9:27 am, <apozdol@xxxxxxxxxxx> <apozdol@xxxxxxxxxxx> wrote:

Might anyone have a gauge tester C-3826 that you may loan out , with a deposit of course?

 

I had my “new” leaking gas tank repaired and sealed and installed a new sending unit after seeing this one which the PO had customized. Had to share, too funny!

I now guess he may have done so because of the fuel gauge malfunctioning.

It never worked correctly as you can imagine with the fuel reading being lower than the actual fuel in the tank.

Now with the new sending unit, my gauge still reads low! I put five gallons of gas into the tank and the gauge barely reads above E, reading low just like before. I bounced the rear end a bunch of times, no change.

I will try a slip on ground clip on the tank in a bit, but I sure would like to check each component for prescribed resistance.

Does the gas gauge have any adjustments, or is it just resistors?

 

Allan

 

--
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/006101d821af%24017b97a0%240472c6e0%24%40comcast.net.
<Resized_20220207_141647.jpeg>

--
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit
https://groups.google.com/d/msgid/chrysler-300-club-international/DEC08A58-E6B6-4952-B1E6-519240AC44EC%40gradyresearch.com
.

--
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit
https://groups.google.com/d/msgid/chrysler-300-club-international/1761583805.875622.1644858861988%40mail.yahoo.com
.

--
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/1993434491.1194425.1644864144906%40mail.yahoo.com.


Home Back to the Home of the Forward Look Network Archive Sitemap


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.