Re: {Chrysler 300} Question on installing spring clips for nose letters
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: {Chrysler 300} Question on installing spring clips for nose letters on my 1959 300 E




Thanks Henry…good advice…
I’ll try to manage the size of the sides of clip a bit and fit it in.
Would 3M Super Adhesive Weatherstrip work
the same as JB Weld?

Rob 

Robert T. Lutts, President and Chief Investment Officer
Cabot Wealth Management, Inc.
216 Essex Street
Salem, Massachusetts 01970
978-979-0880
www.eCabot.com


From: chrysler-300-club-international@xxxxxxxxxxxxxxxx <chrysler-300-club-international@xxxxxxxxxxxxxxxx> on behalf of Henry A. Mitchell III <hamlll@xxxxxxxxxxxxxx>
Sent: Monday, September 5, 2022 6:16 PM
To: Rob Lutts <Rob@xxxxxxxxxx>; 'Ron Waters' <ronbo97@xxxxxxxxxxx>; 'Chrysler 300 Club International' <chrysler-300-club-international@xxxxxxxxxxxxxxxx>
Subject: RE: {Chrysler 300} Question on installing spring clips for nose letters on my 1959 300 E
 

[EXTERNAL EMAIL]

HiHo Rob: your hood is original. All the undersides of the C-D-E hoods are not that accessible….otherwise, the letters would go on with a speed nut like the rear license plate frame/�300� letters, or a threaded stud like the trunk medallion. I do not recommend making the hole bigger; I think that would just make the clip looser. Instead, try bending the side tangs that hold the clip in the hole (see jpg attached) to make the clip tighter in the hole. You will really have to push the clip in because, as was observed, it looks like you have a thin layer of bondo around the hole. After the clip is in, I recommend putting just a teeny tiny blob of JB Weld on the shaft of the S to make sure you don’t lose this one. By the way, I have a spare S, as shown in the attached and you are welcome to it. it’s a little janky but it is chrome. I am almost positive I got my clips from Goers/Quirey but I cant lay my hands on the catalog to confirm. I am diligently looking for something else right now because I always find stuff like misplaced catalogs when I am looking for something else.

 

Henry

300C

 

From: chrysler-300-club-international@xxxxxxxxxxxxxxxx <chrysler-300-club-international@xxxxxxxxxxxxxxxx> On Behalf Of Rob Lutts
Sent: Monday, September 05, 2022 2:13 PM
To: Ron Waters <ronbo97@xxxxxxxxxxx>; 'Chrysler 300 Club International' <chrysler-300-club-international@xxxxxxxxxxxxxxxx>
Subject: Re: {Chrysler 300} Question on installing spring clips for nose letters on my 1959 300 E

 

Thanks Ron.

I think that may be the issue...I'll file the sides

of the hole down a bit.  

 

As to photos from below... the lower part of the nose part of the hood

is not accessible...it's wrapped in metal. Maybe my hood

is different from original.

 

Rob

 

Robert T. Lutts, President and Chief Investment Officer

Cabot Wealth Management, Inc.

216 Essex Street

Salem, Massachusetts 01970

978-979-0880

 


From: chrysler-300-club-international@xxxxxxxxxxxxxxxx <chrysler-300-club-international@xxxxxxxxxxxxxxxx> on behalf of Ron Waters <ronbo97@xxxxxxxxxxx>
Sent: Monday, September 5, 2022 5:07 PM
To: 'Chrysler 300 Club International' <chrysler-300-club-international@xxxxxxxxxxxxxxxx>
Subject: RE: {Chrysler 300} Question on installing spring clips for nose letters on my 1959 300 E

 

[EXTERNAL EMAIL]

Rob -

 

The pin goes thru the hole. Then the retainer slides onto the pin on the back side of the hood.

 

From your photos it appears that you may have a layer of body filler that may impede the pin from sliding fully thru the hole. Please shoot a picture from underneath the hood showing how far the pin protrudes thru the hole.

 

Thanks,

 

Ron

 


From: chrysler-300-club-international@xxxxxxxxxxxxxxxx [mailto:chrysler-300-club-international@xxxxxxxxxxxxxxxx] On Behalf Of Larry Jabin
Sent: Monday, September 05, 2022 1:46 PM
To: rob; Chrysler 300 Club International
Subject: RE: {Chrysler 300} Question on installing spring clips for nose letters on my 1959 300 E

I have the same situation please include me an any reply’s

 

 

Thank You

 

Larry

 

From: chrysler-300-club-international@xxxxxxxxxxxxxxxx <chrysler-300-club-international@xxxxxxxxxxxxxxxx> On Behalf Of rob
Sent: Monday, September 5, 2022 9:20 AM
To: Chrysler 300 Club International <chrysler-300-club-international@xxxxxxxxxxxxxxxx>
Subject: {Chrysler 300} Question on installing spring clips for nose letters on my 1959 300 E

 

Hello 300 Group

 

About three months ago after a nice Sunday drive I discovered my LETTER

“Sâ€? on the hood nose of my 300 had disappeared.  I suspect it just fell out.

I was able to find a replacement S from the Quigly company. It is 

not chromed…but it will do. Then I learned I needed a set of spring clips

to properly attach it.  I was able to get the spring clips…a set of 8! 

Now the challenge of how to properly install it? I tried putting it in the hole

and gently tapping the clip. This did not work adequately. Then I tried

attaching it first to the post of the letter and gently tapping that into

the hole. This resulted in the post on the letter bending. Any advice on how

to properly install my new letter.  I did think about using adhesive….

however the proximity to the radiator leads me to believe an adhesive will fail due to the heat.  

I will be grateful for some good advice?

Here’s a few photos….

 

Thanks.  

Rob

 

--
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/d240f85a-f0e6-467a-a58e-659aca6bb88bn%40googlegroups.com.

--
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/8f136bc4a30749ab8fddf4b48111c2d1%40pwbsfo.com.

--
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to a topic in the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this topic, visit https://groups.google.com/d/topic/chrysler-300-club-international/-IBL3XA7SqA/unsubscribe.
To unsubscribe from this group and all its topics, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/ABA2D12B59E84BA3AACC545109A0D42E%40ThinkPadL520.

--
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/BL3PR04MB81712E2E54F10A964068CAC9D47F9%40BL3PR04MB8171.namprd04.prod.outlook.com.




Avast logo

This email has been checked for viruses by Avast antivirus software.
www.avast.com


--
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to a topic in the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this topic, visit https://groups.google.com/d/topic/chrysler-300-club-international/-IBL3XA7SqA/unsubscribe.
To unsubscribe from this group and all its topics, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/001001d8c174%24fdeb8f30%24f9c2ad90%24%40mindspring.com.

--
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/BL3PR04MB8171EDD69AAC3AF80C7B5606D47E9%40BL3PR04MB8171.namprd04.prod.outlook.com.


Home Back to the Home of the Forward Look Network Archive Sitemap


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.