Re: {Chrysler 300} 1960 300F Wheel Cylinders
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: {Chrysler 300} 1960 300F Wheel Cylinders



I second Bob’s recommendation to use DOT 5. I performed a complete brake restoration  on 2011 on my 62 Sport Conv. Using DOT 5 - still looks new. I do have a tag attached to the master cylinder top that says DOT 5.

Sent from my iPhone

On Jan 11, 2023, at 9:48 AM, Ray Jones <1970hurst@xxxxxxxxx> wrote:


There was a company in WV that resleeved them and M/C also. Not sure if still in business.
Ray

On Wed, Jan 11, 2023 at 8:30 AM John Grady <jkg@xxxxxxxxxxxxxxxxx> wrote:
Wheel cylinders are pretty basic cast iron   I would expect any that you find new would work . Be sure you are aware Rand L are unique . 
I assume you have the pits in the bottom from glycol fluid left in too long ? Very smart to change them . That is a disaster waiting to happen . And not uncommon , happened to me . Water settles out the there once glycol is saturated with water , makes a pit under lip of seal . And that always  happens given enough time . . Why Mercedes requires change of glycol brake fluid every few years . I ignored that as too conservative on an 80 300 TD wagon , cost me 2000 in brake parts rusted inside after ten years .causes leaks in drum brakes , stuck calipers on discs . 
One of the main reasons I love silicone in our cars despite fussiness of getting in right . 
Ideal for stored cars , it will not absorb water why military uses it . And rubber loves it . 
If you shake it or get air in it you have to wait months . Really 

I found large cans on line long ago military surplus .
John 

Sent from my iPhone

On Jan 11, 2023, at 6:08 AM, Nick Taylor <nicksgaragesd@xxxxxxxxx> wrote:


We got the centric ones for a 1961 Belvedere and the lower fronts have the bleeders too close to the steering. Also, it took three different sizes of wrenches for the bleeder screws. 

On Wed, Jan 11, 2023, 2:01 AM Marshall Larson <granitledge@xxxxxxxxx> wrote:
I have the Centrics in three cars. Functioning properly.

On Tue, Jan 10, 2023 at 8:29 PM Jim Birr <jebirr@xxxxxxxxx> wrote:
Hi everyone.  Looking to pickup new wheel cylinders for my F.  Found following sources and rough prices:
  • Andy Bernbaum - $40 ea
  • Rock Auto - Dynamic Friction $16.60/ea
  • Rock Auto - Centric $18/ea
  • MoParPRO - All six for $179
  • NAPA only has rear for $65
Anybody have any experience with any of these vendors for brake cylinders?  Andy B. seems a bit pricey.   Not sure if Dynamic Friction or Centric products are any good.  Heard some negative on other Centric products.  MoParPro is an unknown.

Thanks in advance.

Jim

--
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/b9965624-aa93-4c72-94ac-64b86f921025n%40googlegroups.com.


--
Marshall Larson

--
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/CACuDFNRiFLWpwgy7P_EXKew4v9z-KD3iAuwPj2iY666Sx%3Dzk-A%40mail.gmail.com.

--
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/CA%2BjApFMUBNvocX%3DXjq%3DRfVoOnqxuDVs6G2srjywmVGsx8OK5Yw%40mail.gmail.com.

--
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/C38B2382-AB93-4555-BA4E-BCEFF95286FB%40gradyresearch.com.


--
Ray Jones. Y'all come on down an see us. Ya hear?

--
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/CAD72c-yH4wQE-L2e9p1xtxr6km%2B8qhW3BdHC3TPju6PYtgniXg%40mail.gmail.com.

--
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/95EA0627-6680-44F6-AE12-FDCB2DC5BA65%40comcast.net.


Home Back to the Home of the Forward Look Network Archive Sitemap


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.