Re: {Chrysler 300} Oil Filter Gasket
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: {Chrysler 300} Oil Filter Gasket



Hi the stock  setup is ok once calmed down , oil spill mess is the issue . They changed millions of those in the day .
But I think you are correct ,the following  comment is only from memory , I think there is supposed to be (?) a copper washer between the bolt head and filter can . 
I have found those copper washers  in general on ebay or amazon , .. find ID of washer to pick by measuring stem .
It seals on the two faces , so even slightly loose on bolt will work  ( often washers today are offshore metric) . Or maybe someone like Andy Bernbaum has the mopar one .  
Related and tricky , again from memory  , incompetents often overtightened them ( there is a spec , use it ) resulting in either bottoming out of thread or denting in the top of the can , making it shorter , then it leaks forever . Cure might be a machine shop or press to push pout again but top  has to be level after,  to seal 360 . 

An alternative might be two stock washers stacked , possibly with RTV or weatherstrip cement holding them together , that would give you ?.030 more sealing “ crush”, even with a  dented in can  . And use correct torque 
The ws cement can help hold the block side gasket in place too . I found out it is good  for like 400F once cured —and
 3M recommends it as a gasket sealer  . I love the stuff , a few dots get tacky  hold things like oil pan gaskets , while you work . Comes off flat surfaces pretty easy unlike permatex type products , and sometimes RTV success imho  is flaky at best . 
good luck 
john g 
Sent from my iPhone

> On Jul 26, 2023, at 8:24 AM, Zach Hietsch <zhietsch@xxxxxxxxx> wrote:
> 
> Help John and Bob,
> 
> I recently replaced the oil filter on my B and it is leaking from the top where the nut is. The service manual doesn’t show a gasket there. Should there be some sort of gasket other than the one that connects to the block. 
> 
> Also is there an easier way to get the filter on and know that the bottom gasket is lined up correctly other than struggling through the engine bay? 
> 
> I have a spin on filter adapter but I can’t loosen the bolts with the space available around the connector. I’ve been trying to avoid using impacts and power tools because I don’t want to break anything. Should I tempt fate or would removing the wheel well be the best path forward. 
> 
> Any insight would be greatly appreciated.  
> 
> Thanks
> Zach Hietsch
> 
> -- 
> For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
> --- 
> You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
> To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
> To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/F33A084C-32AA-488A-8AB8-FFCD03F6D392%40gmail.com.

-- 
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
--- 
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/79C970EC-80DE-4168-9333-BBFEDBA6A4D1%40gradyresearch.com.


Home Back to the Home of the Forward Look Network Archive Sitemap


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.