Re: Exhaust "bypass" valve? Also..timing
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: Exhaust "bypass" valve? Also..timing



LOTS of things play into properly running motor, Fuel, Carburetor,
Distributor, Timing, Exhaust, Temp, Altitude, Spark Plugs, Wires,
Rings, Valves...etc.  There is no "Quick fix" to stop engine pinging.
However there are many common things that cause it and make it really
bad.  First the timing...your car should be as you set it, 10btdc.
However if the fuel you are running is a low octane, or if the motor
is running on the hot side, or if you are up in the mountains it may
be too much.  Try turning it back a few degrees, try 8 or 5 degrees to
see if it likes it better.  Buy the best fuel you can and the highest
octane rating you can find, remember when you car was new regular gas
octane was 93 and Premium was around 101, your car would have run on
93 octane, that today is Premium gas...not regular.  Octane helps to
stop the pinging and regular gas now is MUCH lower octane .  Make sure
the plugs are in good condition as the plug wires.  Make sure the air
filter is clean, and if all that fails, the carburetor maybe out of
adjustment.  But I would do the fuel and adjust the timing to suit the
car.  Remember it's a 50 year old car, it's going to be quirky a bit.
It's not like the new cars on the road today where computers adjust
everything 1000's of times a minute to make them run wonderful.

On Thu, Sep 8, 2011 at 1:33 PM, Jacob Fox <imfast101@xxxxxxxxx> wrote:
> How do I remove/disable the exhaust bypass valve on the exhaust manifold? It rattles and is super noisy going down the road...hopefully it can be done without removal of the manifold. Never removed them and really don't wanna twist any bolts off.
>
> Okay timing. Had a lot of "valve noise" on accelerating and A LOT when I punch it. I removed vacuum line from distributor and adjusted to 10 btdc. Being that 10 is the only number on my timing stub I guess that's what that is. Now after putting it back together and taking it in the road...no difference.  Plus it had a rough idle. Now I noticed when I adjusted it to 10btdc with vacuum advance still on, it idled smoother...didn't have any noise, but taking off and in turns it almost dies...what should I do to get it right!? It doesn't have points, electronic ignition.
>
> Sent from my iPhone
>
> --
> --
> Please address private mail -- mail of interest to only one person -- directly to that person. That is, send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic.  Thanks!
>
> 1962 to 1965 Mopar Clubhouse Discussion Guidelines:
> http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
> --
> You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
> http://groups.google.com/group/1962to1965mopars?hl=en.
>



-- 
Eric
Tacoma, WA
1962 Chrysler Newport 2 door HT

-- 
--
Please address private mail -- mail of interest to only one person -- directly to that person. That is, send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic.  Thanks!

1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
-- 
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
http://groups.google.com/group/1962to1965mopars?hl=en.


Home Back to the Home of the Forward Look Network


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.