RE: Mopar Performance electronic distributor puling
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

RE: Mopar Performance electronic distributor puling



The gaps are even all the way around.  But the pick-up angles back a bit.  Have it set at .008 on the bottom – probably over the 018 tolerance on the upper point.  That pick-up coil gizmo can be wiggled about like it is held in place with magnets.  I assume that is normal.  This is a new P3690426 bought a couple years ago from Summit, and waiting on the shelf since.

 

From: 1962to1965mopars@xxxxxxxxxxxxxxxx [mailto:1962to1965mopars@xxxxxxxxxxxxxxxx] On Behalf Of Herb
Sent: Friday, May 22, 2015 8:42 AM
To: 1962to1965mopars
Subject: Re: Mopar Performance electronic distributor puling

 

Can we go back to the basics for a minute?   Ricky can you clarify on your worrisome statement about the reluctor not being parallel?  It sounds to me like your reluctor is not properly seated in the distributor.  I am taking it that you meant all gaps the same as you spin it, as you checked each lobe to the reluctor and the gap stayed the same?  OK that eliminates a possible bent/jammed shaft.  Please clarify what you meant about not parallel.

 

 

 

 

-------Original Message-------

 

Date: 5/22/2015 7:41:52 AM

Subject: Mopar Performance electronic distributor puling

 

Installed a new Mopar Performance electronic distributor last night.  Starts and idles fine but going down the road while holding steady throttle, the engine pulses up and down every few seconds.  Almost like you are giving it more and less throttle.  The amp meter is also erratic now.

 

Per the instructions the blue wire is connected to the ballast resister ignition feed side.  Black wire to neg side of coil.  And timing to 5 BTDC per the instructions.

I did notice the reluctor and pick-up are not parallel for the .008 gap.  All the same gaps as you spin it, and I did set the closest point to .008. 

Any ideas what the problem is?   Is there another vacuum advance type distributor to consider for electronic ignition?  Pertronix makes one I see that is an all-in-one unit, any other makers for 318 Poly?

I put the original point distributor back on for now, and it runs fine.

Thanks,

Ric

 

 

--
--
--
Please address private email -- email of interest to only one person -- directly to that person. That is, email your parts/car transactions and negotiations, as well as other personal messages, only to the intended recipient. Do not just press "reply" and send your email to everyone using the general '62-'65 Clubhouse public email address. This practice will protect your privacy, reduce the total volume of mail and fine-tune the content signal to Mopar topic. Thanks!
 
1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
--
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
http://groups.google.com/group/1962to1965mopars?hl=en.

---
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
To unsubscribe from this group and stop receiving emails from it, send an email to 1962to1965mopars+unsubscribe@xxxxxxxxxxxxxxxx.
For more options, visit https://groups.google.com/d/optout.

--
--
--
Please address private email -- email of interest to only one person -- directly to that person. That is, email your parts/car transactions and negotiations, as well as other personal messages, only to the intended recipient. Do not just press "reply" and send your email to everyone using the general '62-'65 Clubhouse public email address. This practice will protect your privacy, reduce the total volume of mail and fine-tune the content signal to Mopar topic. Thanks!
 
1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
--
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
http://groups.google.com/group/1962to1965mopars?hl=en.

---
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
To unsubscribe from this group and stop receiving emails from it, send an email to 1962to1965mopars+unsubscribe@xxxxxxxxxxxxxxxx.
For more options, visit https://groups.google.com/d/optout.


Home Back to the Home of the Forward Look Network


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.