The Forward Look Network | ||
| ||
poly intake 1619826 Jump to page : 1 Now viewing page 1 [50 messages per page] | View previous thread :: View next thread |
Forward Look Technical Discussions -> Engine, Exhaust, Fuel and Ignition | Message format |
ttotired |
| ||
Expert 5K+ Posts: 8445 Location: Perth Australia | Hi all I bought this manifold a while ago (poly intake 1619826), but not really sure what its off. It is a 4 barrel, but the base is really small Anyone know what its off and/or what carby fits it? The base is way to small for an edelbrock carby Cheers | ||
wayfarer |
| ||
Elite Veteran Posts: 889 Location: Peoples Republic of Oregon | Can you send or post a photo? | ||
60 dart |
| ||
Expert 5K+ Posts: 8948 Location: WHEELING,WV.>>>HOME OF WWVA | 55 fireflite ---------------------------------------------later | ||
ttotired |
| ||
Expert 5K+ Posts: 8445 Location: Perth Australia | Heres the pictures You think 55 fireflite Chuck (poly intake 001.jpg) (poly intake 002.jpg) (poly intake 003.jpg) (poly intake 004.jpg) (poly intake 005.jpg) Attachments ---------------- poly intake 001.jpg (78KB - 181 downloads) poly intake 002.jpg (98KB - 143 downloads) poly intake 003.jpg (79KB - 148 downloads) poly intake 004.jpg (83KB - 153 downloads) poly intake 005.jpg (84KB - 156 downloads) | ||
60 dart |
| ||
Expert 5K+ Posts: 8948 Location: WHEELING,WV.>>>HOME OF WWVA | ooops , i was lookin at 1618926-------------------------------------------------later | ||
60 dart |
| ||
Expert 5K+ Posts: 8948 Location: WHEELING,WV.>>>HOME OF WWVA | for sure 56-57 plymouth with power package , 277 in 56 , 301 in 57-------------------------------------------later Edited by 60 dart 2014-05-09 1:14 AM | ||
ttotired |
| ||
Expert 5K+ Posts: 8445 Location: Perth Australia | Thanks Chuck I am selling it over here as I dont think I will use it A bit pricey to send back to the US though as with what it cost me to buy it and get it here, by the time it went back, it would be close to a grand | ||
rockerarm |
| ||
Elite Veteran Posts: 873 Location: ALABAMA, HEART OF DIXIE |
You are correct sir. It was designed for use with a Carter WCFB carb. | ||
ttotired |
| ||
Expert 5K+ Posts: 8445 Location: Perth Australia | Look what I just found http://www.ebay.com/itm/Small-Carter-Rochester-WCFB-intake-manifold... | ||
Mopar1 |
| ||
Expert Posts: 3035 Location: N.W. Fla. | ttotired - 2014-05-09 5:51 PM That's going the wrong way, putting a small base WCFB on a large base intake. He needs to put a large carb on the small base. Must be they used a smaller base carb on these, the Edelbrocks fit nicely on the Chrysler hemi intakes if the bore holes are opened up.Look what I just found http://www.ebay.com/itm/Small-Carter-Rochester-WCFB-intake-manifold... | ||
ttotired |
| ||
Expert 5K+ Posts: 8445 Location: Perth Australia | No, its going the right way Putting a larger based asv onto where there was a WCFB carb The manifold base sise is only 3 7/8 x 3 1/2, so even opening the bores will not let an asv (or holley) square bore carb fit. The 58 2x4 manifolds I have, both have the larger mounting bases and with grinding out the bores, an asv will fit, but I put adaptors on mine. There is a 4 barrel manifold on ebay now (think its safety mike's?) that is the later type with the larger carb mounting flange | ||
MoparDon |
| ||
Member Posts: 24 | Are you selling this intake THANKS DON | ||
ttotired |
| ||
Expert 5K+ Posts: 8445 Location: Perth Australia | I dont need it Don, so yes I will send you a pm | ||
Jump to page : 1 Now viewing page 1 [50 messages per page] |
Search this forum Printer friendly version E-mail a link to this thread |
(Delete all cookies set by this site) | |