The Forward Look Network
The Forward Look Network
Search | Statistics | User Listing Forums | Chat | eBay | Calendars | Albums | Skins | Language
You are logged in as a guest. ( logon | register )

'58 New Yorker Coupe
Jump to page : 1 2
Now viewing page 2 [50 messages per page]
View previous thread :: View next thread
   Forward Look NON-Technical Discussions -> Members RidesMessage format
 
Powerflite
Posted 2018-01-11 2:39 PM (#556065 - in reply to #498001)
Subject: RE: '58 New Yorker Coupe



Expert

Posts: 4210
20002000100100
Location: So. California
I took out the #7 piston to find out what would have caused the uneven wear & gouge down the wall, but to my surprise, I found nothing wrong. The rings look great and the wrist pin & clips look good too. The bearings also have very little wear on them. My only conclusion is that someone must have put this motor together and just ignored that bad cylinder wall to run it as is. I'm not sure I want to find out how bad it runs with it like that so I am going to tear it apart and sleeve it.



(392No7Piston.jpg)



(Gouge & Uneven Wear.jpg)



Attachments
----------------
Attachments 392No7Piston.jpg (129KB - 18 downloads)
Attachments Gouge & Uneven Wear.jpg (84KB - 19 downloads)
Top of the page Bottom of the page
mikes2nd
Posted 2018-01-11 11:29 PM (#556084 - in reply to #498001)
Subject: Re: '58 New Yorker Coupe


Expert

Posts: 2752
20005001001002525
dude that sucks...
Top of the page Bottom of the page
Powerflite
Posted 2018-01-14 2:39 AM (#556192 - in reply to #498001)
Subject: Re: '58 New Yorker Coupe



Expert

Posts: 4210
20002000100100
Location: So. California
Yeah, it's not great, but I can't really complain since I picked up this mostly complete motor with transmission for $1100. You can't really touch a 392 for that amount anymore. But I don't like the looks of these pistons. Looks like really lame compression ratio. I may run them with 331 heads which will boost it up 1 point, or install forged high compression pistons I have laying around. I haven't decided yet. The forged pistons have aluminum rods on them that I ran in my Barracuda during high school....
Top of the page Bottom of the page
mikes2nd
Posted 2018-01-14 10:23 AM (#556201 - in reply to #498001)
Subject: Re: '58 New Yorker Coupe


Expert

Posts: 2752
20005001001002525
I don't understand how that happens. Also I do see a fair amount of cheap blocks running around. The gouge is too deep to bore it out?

that's a good price, kind of like me. I got my whole car for 3500$ with a good hemi(non running) but had very low wear and turned over so I rebuilt it. Salvaged what I could from the wagon.(took the power steering, power brakes, front end, misc parts...
Top of the page Bottom of the page
Powerflite
Posted 2018-01-14 4:41 PM (#556226 - in reply to #498001)
Subject: Re: '58 New Yorker Coupe



Expert

Posts: 4210
20002000100100
Location: So. California
The bore is already at 30 over; maybe it will come out with 60 over, but maybe not. I hate to bore everything huge to fit one bad bore.
Top of the page Bottom of the page
billy
Posted 2018-04-09 2:33 PM (#561314 - in reply to #498001)
Subject: Re: '58 New Yorker Coupe



Veteran

Posts: 240
10010025
Location: upstate new york
Hey Nathan, I had a Barracuda in high school also...72,,, 340 automatic.....it was the terror of my town...40 yrs ago...:)
Top of the page Bottom of the page
Powerflite
Posted 2018-04-09 4:59 PM (#561323 - in reply to #498001)
Subject: Re: '58 New Yorker Coupe



Expert

Posts: 4210
20002000100100
Location: So. California
Cool, mine was a '68 with the 392 hemi & 4 speed in it. It was a lot of fun, but the motor sits better in a New Yorker.
Top of the page Bottom of the page
Powerflite
Posted 2018-04-29 8:45 PM (#562496 - in reply to #498001)
Subject: RE: '58 New Yorker Coupe



Expert

Posts: 4210
20002000100100
Location: So. California
This car is getting a frame-off job. Hope to get the frame ground, sanded & painted quickly & transferred to the body so I don't have issues with the neighborhood. But I will take some time to replace the brake & fuel lines first. I am thinking of following Mike2nd's lead and using '57 Chevy poly body mounts to replace the rubber ones.

...and just to remind myself, I need to remember to clean up the T-bar adjuster bolts & replace the shocks before it happens to make those tasks much easier than they would be with the body in place. I am also seriously considering welding up the exhaust first too, but I don't know if I can ensure it would work out once the body, fuel tank & drivetrain came into place.

Edited by Powerflite 2018-04-29 8:50 PM




(58ChryslerFrame.jpg)



Attachments
----------------
Attachments 58ChryslerFrame.jpg (225KB - 8 downloads)
Top of the page Bottom of the page
mikes2nd
Posted 2018-04-29 11:14 PM (#562508 - in reply to #498001)
Subject: Re: '58 New Yorker Coupe


Expert

Posts: 2752
20005001001002525
copy cat! interesting you have a flat rubber bushing on the back frame mount.

The dodge has a thing rubber washer and a 'steel bowl', the nut is welded to the frame back there.

I got in space jam and rushed to get the body on the frame, I did get the brake line run but that's it, I would have liked to do the whole deal(engine, drivetrain, rear axle painted, rear brakes etc).

But I will just suffer No more frame sitting out in the driveway.
Top of the page Bottom of the page
Powerflite
Posted 2018-05-01 12:39 PM (#562612 - in reply to #498001)
Subject: RE: '58 New Yorker Coupe



Expert

Posts: 4210
20002000100100
Location: So. California
Yeah, I'm in a hurry to get it swapped too, so I can't afford the body-off convenience that I would like. I paid my son to grind the frame and get it ready to paint. He did a good job. I only had to clean up a couple of areas afterward. I couldn't attach the shocks because they aren't quite long enough when fully extended and I don't have enough weight to compress the springs so this will have to do until I get the body back onto it. I just need to allow the paint to dry so I can install the new lines.



(Painted Frame.jpg)



Attachments
----------------
Attachments Painted Frame.jpg (245KB - 8 downloads)
Top of the page Bottom of the page
mikes2nd
Posted 2018-05-01 1:21 PM (#562613 - in reply to #498001)
Subject: Re: '58 New Yorker Coupe


Expert

Posts: 2752
20005001001002525
wow that was quick... presto painted frame! looks great. Run your brake line and fuel line. How is your underbody?

I spent a ton of time getting that 100%... little issues all over but I got them all.

I protected mine so you cant get water sitting anywhere anymore. Like the trunk support brackets(i seam sealed the edges but left the drain holes so water wont wick up back there) and then coated the whole thing.
Top of the page Bottom of the page
Powerflite
Posted 2018-05-01 2:08 PM (#562617 - in reply to #498001)
Subject: Re: '58 New Yorker Coupe



Expert

Posts: 4210
20002000100100
Location: So. California
My frame has a lot of crud collected inside it at the bottom of the downturn before the axle. I am thinking of drilling a large drain hole in the bottom of it there to get it out and to prevent future issues. The body is really clean so there is very little, if any, rust repair to do on it. That's the good part. So just a little clean up, paint and it should be ready to go. But there is a dent that needs repair near a body mount that I will take care of before the body comes down.
Top of the page Bottom of the page
mikes2nd
Posted 2018-05-01 5:31 PM (#562628 - in reply to #498001)
Subject: Re: '58 New Yorker Coupe


Expert

Posts: 2752
20005001001002525
I drilled some extra holes at the bottom low points and at the bottom outside ends of the rear cross brace.
Top of the page Bottom of the page
Powerflite
Posted 2018-05-17 12:43 PM (#563569 - in reply to #498001)
Subject: RE: '58 New Yorker Coupe



Expert

Posts: 4210
20002000100100
Location: So. California
These extended mounts were placed on one mount in the center of the body, in addition to rubber donuts. Underneath one of them, the frame mount had been hit and bent. I believe that caused a weird bend in the quarter panel that's going to be real fun to take out. I have no idea why they would jack up the car in the center like this. I couldn't remove them without cutting the bolt heads off. They're not going back in.



(Extended Mounts.jpg)



Attachments
----------------
Attachments Extended Mounts.jpg (143KB - 4 downloads)
Top of the page Bottom of the page
mikes2nd
Posted 2018-05-17 7:37 PM (#563589 - in reply to #498001)
Subject: Re: '58 New Yorker Coupe


Expert

Posts: 2752
20005001001002525
dude that weird. How in the heck did they even get in there?
Top of the page Bottom of the page
Powerflite
Posted 2018-05-17 7:59 PM (#563590 - in reply to #498001)
Subject: Re: '58 New Yorker Coupe



Expert

Posts: 4210
20002000100100
Location: So. California
Yeah, no idea why or how they got there. Putting the body on the other frame, they hinder the body from sitting flat so it doesn't seem to like them there. Maybe the original frame was poorly made with the brackets too low? I can't figure it out now because I already scrapped that frame.

Edited by Powerflite 2018-05-17 8:04 PM
Top of the page Bottom of the page
Jump to page : 1 2
Now viewing page 2 [50 messages per page]
Jump to forum :
Search this forum
Printer friendly version
E-mail a link to this thread


(Delete all cookies set by this site)