The Forward Look Network | ||
| ||
Rack and Pinion Steering Jump to page : 1 Now viewing page 1 [50 messages per page] | View previous thread :: View next thread |
Forward Look Technical Discussions -> Steering and Suspension | Message format |
1956RoyalLancer |
| ||
Member Posts: 7 Location: Port Washington, New York (Long Island( | Hello, Does anyone know if I can put rack and pinion steering in my 1956 Dodge Royal Lancer? | ||
DepsilonD |
| ||
Elite Veteran Posts: 792 Location: Buena Park, CA | Its a tough conversion from what I have read. I think Fatman Fab may offer some form of kit but my memory is hazy on the subject. | ||
ttotired |
| ||
Expert 5K+ Posts: 8443 Location: Perth Australia | Anything can be done Bolt in kit, I don't think so, but a mustang 2 frontend grafted into the chassis will give you rack and pinion as well as coil spring front suspension (read air bags) and easy disc brakes. It will also give you a much lighter wallet and plenty of distain from the purists It really depends on why you want it, modding the car, go for it, just want power steering, chase up the factory parts, would be cheaper and easier | ||
LostDeere59 |
| ||
Extreme Veteran Posts: 406 Location: Hilltown, PA | Another popular option is the 2003-up Crown Vic/Grand Marquis crossmember/suspension clip. Disc brakes, coil over struts, rack and pinion, plus newer parts availability. It's something I'm considering myself . . . Gregg | ||
Old Ray |
| ||
Extreme Veteran Posts: 507 Location: Invermere B.C. Canada - Rocky Mountains | LostDeere59 - 2018-05-30 7:04 PM Another popular option is the 2003-up Crown Vic/Grand Marquis crossmember/suspension clip. Disc brakes, coil over struts, rack and pinion, plus newer parts availability. It's something I'm considering myself . . .Gregg Gregg, not on the somewhat narrow track of the early forward look cars, the track / tread on the CV is too wide. The "flavor of the week" is the front frame portion from a Dakota. At the sweet spot, the frames are identical, track is close. Lots of info on both on the net. NOT that I would ever consider doing this, NEVER. Not mine: (dakota into '57 ply steering # 2.jpg) Attachments ---------------- dakota into '57 ply steering # 2.jpg (55KB - 228 downloads) | ||
57chizler |
| ||
Expert Posts: 3777 Location: NorCal | The GM Cavalier rack is popular for swaps, it's rear-mounted and the center-steer design eliminates a lot of the bump steer that's common in R&P swaps. If you don't have fabrication skills, forget it. http://www.crankshaftcoalition.com/wiki/Swapping_to_rack_and_pinion... | ||
LostDeere59 |
| ||
Extreme Veteran Posts: 406 Location: Hilltown, PA | That's interesting Ray - I never would have thought of that (until I got my tape measure out of course). I've seen the CV?GM suspension in several cars at shows - I thought one of them was a FL but I might be wrong (pretty likely). Gregg | ||
Old Ray |
| ||
Extreme Veteran Posts: 507 Location: Invermere B.C. Canada - Rocky Mountains | LostDeere59 - 2018-06-01 10:05 AM That's interesting Ray - I never would have thought of that (until I got my tape measure out of course). I've seen the CV?GM suspension in several cars at shows - I thought one of them was a FL but I might be wrong (pretty likely). Gregg Greg, here is a teaser for you; (plymouth dakota frame 4.jpg) Attachments ---------------- plymouth dakota frame 4.jpg (57KB - 211 downloads) | ||
Old Ray |
| ||
Extreme Veteran Posts: 507 Location: Invermere B.C. Canada - Rocky Mountains | ........look what I found in my picture files when I was looking for the above picture; (plymouth 1958 dakota steering and booster 2.jpg) Attachments ---------------- plymouth 1958 dakota steering and booster 2.jpg (162KB - 213 downloads) | ||
littlecarl |
| ||
Extreme Veteran Posts: 337 Location: UK | Old Ray - 2018-06-01 1:59 AM ........look what I found in my picture files when I was looking for the above picture;
What size wheels are you running on that Dakota setup? Ideally I would like to keep using 14" or at least 15" wheels. | ||
Jump to page : 1 Now viewing page 1 [50 messages per page] |
Search this forum Printer friendly version E-mail a link to this thread |
(Delete all cookies set by this site) | |