The Forward Look Network
The Forward Look Network
Search | Statistics | User Listing Forums | Chat | eBay | Calendars | Albums | Skins | Language
You are logged in as a guest. ( logon | register )

Gen 1 Hemi Spark Plug Wire Control Clips PN 1483 579
Jump to page : 1
Now viewing page 1 [50 messages per page]
View previous thread :: View next thread
   Forward Look Technical Discussions -> Engine, Exhaust, Fuel and IgnitionMessage format
 
56D500boy
Posted 2024-01-13 1:42 PM (#633380)
Subject: Gen 1 Hemi Spark Plug Wire Control Clips PN 1483 579



Exner Expert 10K+

Posts: 10238
5000500010010025
Location: Lower Mainland BC
.
These clips have been discussed before in a thread about a 57 New Yorker (with a 392 hemi). I was and still am looking for a set of clips.

The clips are used to control the spark plug wires under wire cover before the cover is placed over the wires.

There are 6 clips in a set for cylinders 3,4,5,6,7 and 8, i.e. at 7 and 8 the clips control 4 wires, at 5 and 6 three wires and at 3 and 4 two wires. Once past 3 and 4, there is just one spark plug wire heading to 1 and 2.

The clip:



Some clips in action:



PN listing for the clips (I just did a search at all my known NOS suppliers on 1483579 and came up dry):



REFERENCE: Previous discussion: http://www.forwardlook.net/forums/forums/thread-view.asp?tid=63695&...

REFERENCE: Dodge Spark plug wire cover info: http://www.forwardlook.net/forums/forums/thread-view.asp?tid=79122

Top of the page Bottom of the page
wayfarer
Posted 2024-01-13 2:23 PM (#633381 - in reply to #633380)
Subject: Re: Gen 1 Hemi Spark Plug Wire Control Clips PN 1483 579



Elite Veteran

Posts: 903
500100100100100
Location: Peoples Republic of Oregon
I looked into making some of these many years ago but no demand equals dead inventory. I had talked with the owner of a sheetmetal shop and he thought it would be easy enough to make them out of a spring steel material. The usual problem was either make a few at $$$ or make hundreds at $.
Not sure of the market today as many of the hot-rod crowd don't run the covers.
Top of the page Bottom of the page
22mafeja
Posted 2024-01-16 3:10 AM (#633405 - in reply to #633380)
Subject: RE: Gen 1 Hemi Spark Plug Wire Control Clips PN 1483 579


Elite Veteran

Posts: 714
500100100
Location: Finland
I would make them of 0,5mm stainless. The spring tension is enough , they just stay there and not rattle.
I made 2 pc just for fun from a scrap piece and that took 10 minutes...anybody can...



(20240116_094425fwl2.jpg)



Attachments
----------------
Attachments 20240116_094425fwl2.jpg (227KB - 65 downloads)
Top of the page Bottom of the page
Mopar1
Posted 2024-01-16 9:57 AM (#633407 - in reply to #633381)
Subject: Re: Gen 1 Hemi Spark Plug Wire Control Clips PN 1483 579



Expert

Posts: 3082
20001000252525
Location: N.W. Fla.
wayfarer - 2024-01-13 1:23 PM
Not sure of the market today as many of the hot-rod crowd don't run the covers.
I run covers & they don't seem necessary.
Top of the page Bottom of the page
56D500boy
Posted 2024-01-16 11:05 AM (#633409 - in reply to #633405)
Subject: RE: Gen 1 Hemi Spark Plug Wire Control Clips PN 1483 579



Exner Expert 10K+

Posts: 10238
5000500010010025
Location: Lower Mainland BC
.
Ralf: Did you create that rolled edge or did your starting "scrap" piece already have that ?



(RalfsDIYHemiSparkPlugWireClip.jpg)



Attachments
----------------
Attachments RalfsDIYHemiSparkPlugWireClip.jpg (147KB - 72 downloads)
Top of the page Bottom of the page
56D500boy
Posted 2024-01-16 1:57 PM (#633410 - in reply to #633409)
Subject: RE: Gen 1 Hemi Spark Plug Wire Control Clips PN 1483 579



Exner Expert 10K+

Posts: 10238
5000500010010025
Location: Lower Mainland BC
.
Del S just emailed me with

"I had one of these when I was building airplanes but someone liked it more than I did. (they got stolen)
I would have added to your thread but I do not have my laptop here.
Or... maybe you could ???? "

Sure Del. No problemo.





(DelSsEdgeRollingPliers.jpg)



Attachments
----------------
Attachments DelSsEdgeRollingPliers.jpg (141KB - 70 downloads)
Top of the page Bottom of the page
22mafeja
Posted 2024-01-17 2:20 AM (#633415 - in reply to #633380)
Subject: RE: Gen 1 Hemi Spark Plug Wire Control Clips PN 1483 579


Elite Veteran

Posts: 714
500100100
Location: Finland
Dave ,I started with a flat sheet.The edge I formed in my terrible wise(a shame)....just a number of gentle taps with a hammer needed. I used a 30x30x3 flat bar piece
to get a clean edge to hammer against.
That`s a smart tool with bead rollers...

Edited by 22mafeja 2024-01-17 2:24 AM
Top of the page Bottom of the page
Jump to page : 1
Now viewing page 1 [50 messages per page]
Jump to forum :
Search this forum
Printer friendly version
E-mail a link to this thread

* * * This site contains affiliate links for which we may be compensated * * *


(Delete all cookies set by this site)