Re: IML: 60 fuel sender unit
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: IML: 60 fuel sender unit



The new external limiter fastens to the back of the gauge cluster, and will have to be wired in. The mounting point serves as ground. The OIC web site fully explains the process. When I did all of my cars years ago, I was able to use all of the existing wiring, and simply by pass the old connection to the failed limiter. The new limiter has been said to be available at NAPA. The part number should be on the OIC web site. Good luck.

Paul W.

-----Original Message-----
From: randalpark@xxxxxxx
To: mailing-list@xxxxxxxxxxxxxxxx
Sent: Wed, 9 May 2007 2:13 PM
Subject: Re: IML: 60 fuel sender unit

That is because the voltage limiter has failed.

Paul W.

-----Original Message-----
From: shelbyguy@xxxxxxx
To: mailing-list@xxxxxxxxxxxxxxxx
Sent: Wed, 9 May 2007 12:53 PM
Subject: Re: IML: 60 fuel sender unit

Thanks for all the responses. I unplugged the sender and the fuel gauge obviously reads E but the temp and oil pressure still peg at the high side
and...I don't know where I put my FSM
Tom
----- Original Message ----- From: "Rob Kidd" <rlkidd@xxxxxxxxxxxxxxxx>
To: <mailing-list@xxxxxxxxxxxxxxxx>
Sent: Wednesday, May 09, 2007 4:28 PM
Subject: Re: IML: 60 fuel sender unit

Try unplugging the sender at the tank again. The
rheostat may be bad in the new part.



On Wed, 9 May 2007 12:10:52 -0700 (PDT)
tom higgins <thomash85715@xxxxxxxxx> wrote:
Why would this happen at the same time as the sender was
being changed out? Just a coincidence? Tom said the
other gauges read normal until the replacement device went
in.

randalpark@xxxxxxx wrote: The internal voltage limiter
has failed. You will need to bypass it and
install an external one on the back of the cluster. By
being pegged the
gauges are receiving too much voltage, so they will burn
out very soon
if you don't disconnect them.

There is information about this at ther OIC web site.

Paul W.

-----Original Message-----
From: shelbyguy@xxxxxxx
To: mailing-list@xxxxxxxxxxxxxxxx
Sent: Wed, 9 May 2007 10:46 AM
Subject: Re: IML: 60 fuel sender unit

Well, I got my rebuilt fuel sender for my 60 Crown back
last night and
I just got finished installing it. Prior to the rebuild,
my fuel gauge
remained on E at all times. The oil pressure gauge worked
as did the
temperature and ammeter gauges. Now, after installing the
rebuilt fuel
sender, the fuel gauge registers FULL even though I know
there is only
3 gallons in the tank, the temp gauge pegged at H as did
the oil
pressure gauge. Anybody have any ideas what happened?
Thanx
Tom
60 4dr Crown Southampton.
----------------- http://www.imperialclub.com
----------------- >>This message was sent to you by the Imperial
Mailing List.
Please reply
to mailing-list@xxxxxxxxxxxxxxxx and your response will be
shared with
everyone. Private messages (and attachments) for the
Administrators should be sent to
webmaster@xxxxxxxxxxxxxxxx
To UN-SUBSCRIBE, go to
http://imperialclub.com/unsubscribe.htm



_______________________________________________________________________

_
AOL now offers free email to everyone. Find out more about
what's free
from AOL at AOL.com.
=0


----------------- http://www.imperialclub.com
-----------------
This message was sent to you by the Imperial Mailing List.
Please
reply to mailing-list@xxxxxxxxxxxxxxxx and your response
will be
shared with everyone. Private messages (and attachments)
for the
Administrators should be sent to
webmaster@xxxxxxxxxxxxxxxx
To UN-SUBSCRIBE, go to
http://imperialclub.com/unsubscribe.htm




---------------------------------
Bored stiff? Loosen up...
Download and play hundreds of games for free on Yahoo!
Games.



----------------- http://www.imperialclub.com -----------------
This message was sent to you by the Imperial Mailing List. Please
reply to mailing-list@xxxxxxxxxxxxxxxx and your response will be
shared with everyone. Private messages (and attachments) for the
Administrators should be sent to webmaster@xxxxxxxxxxxxxxxx
To UN-SUBSCRIBE, go to http://imperialclub.com/unsubscribe.htm
----------------- http://www.imperialclub.com -----------------
This message was sent to you by the Imperial Mailing List. Please reply to mailing-list@xxxxxxxxxxxxxxxx and your response will be shared with everyone. Private messages (and attachments) for the
Administrators should be sent to webmaster@xxxxxxxxxxxxxxxx
To UN-SUBSCRIBE, go to http://imperialclub.com/unsubscribe.htm


________________________________________________________________________ AOL now offers free email to everyone. Find out more about what's free from AOL at AOL.com.
=0

----------------- http://www.imperialclub.com -----------------
This message was sent to you by the Imperial Mailing List. Please reply to mailing-list@xxxxxxxxxxxxxxxx and your response will be shared with everyone. Private messages (and attachments) for the
Administrators should be sent to webmaster@xxxxxxxxxxxxxxxx
To UN-SUBSCRIBE, go to http://imperialclub.com/unsubscribe.htm
________________________________________________________________________
AOL now offers free email to everyone. Find out more about what's free from AOL at AOL.com.


-----------------  http://www.imperialclub.com  -----------------
This message was sent to you by the Imperial Mailing List. Please reply to mailing-list@xxxxxxxxxxxxxxxx and your response will be shared with everyone. Private messages (and attachments) for the
Administrators should be sent to webmaster@xxxxxxxxxxxxxxxx
To UN-SUBSCRIBE, go to http://imperialclub.com/unsubscribe.htm



Home Back to the Home of the Forward Look Network


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.