Re: IML: 61 rear brake drum challenge - Tools
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: IML: 61 rear brake drum challenge - Tools



This point, along with safety, can not be over emphasized with respect to this job. The highest quality heavy duty puller makes the difference between success and failure in doing this job.

If you own a tapered rear axle car (pre-1965) and plan to keep it, buying one of these will never be a mistake. If you don't use it, the person who ends up fixing your car will.

Paul W.

-----Original Message-----
From: imperialken@xxxxxxxxx
To: mailing-list@xxxxxxxxxxxxxxxx
Sent: Tue, 15 May 2007 2:58 PM
Subject: RE: IML: 61 rear brake drum challenge - Tools

I've been reading as different members describe horrors related to various repairs of there Imperials. And while I applaud anyone who can save a few bucks during the process, my experience has taught me that "tools" is not
the place to cut corners.  The MAC puller referenced below is a quality
tool. (and it's not cheap) Sure you can get the same tool at Harbor Freight for a fraction of the cost. But it WILL NOT do the same job. I have seen
people spend many a frustrating hour trying to accomplish something with
inferior tools, only to fail.  I'll walk up with Snap-On, Mac or good
Craftsman tools and perform the same task in seconds.  To me the better
tools are worth it.

Just my .02

Ken
67 Crown 4 Dr Ht
68 LeBaron 4 Dr Ht



-----Original Message-----
From: mailing-list-owner@xxxxxxxxxxxxxxxx
[mailto:mailing-list-owner@xxxxxxxxxxxxxxxx] On Behalf Of Kenyon Wills
Sent: Tuesday, May 15, 2007 11:10 AM
To: mailing-list@xxxxxxxxxxxxxxxx
Subject: Re: IML: 61 rear brake drum challenge


--- spicemanii@xxxxxxx wrote:

The hub puller I have is from Mac Tools. I bought
the extra legs, so it has 5 and not 3.

The part # for the
puller: PP827B.  The 2 more legs that you also want
are #PP827B-2. The assembly was $145.99 and the 2
extra legs were $99.10. They paid shipping. Joe
Machado


Joe is right on with that information.  If the MAC
tool fails to pull your drum off, especially with a
good pneumatic impact wrench driving it (manual stuff
is for the birds in my book), your junk just isn't
coming apart and you might want to pass and move
forward to a replacement axle or cut your drum off.

I have plenty of grease on the tool's threads and on
the face where it meets and spins on the axle spindle
too, so that my twisting force is retarded as little
as possible by friction where there's metal twisting
on metal.

I pulled a pair of 1960 Fury (tapered) drums (that I'd
never pulled off before) yesterday with this
discussion in mind as I did it.

once the tool was set up and snug, each drum took less
than 15 seconds of pneumatic impact wrench pressure to
pop, and that's about normal per my experience.

I keep expecting to get a "stubborn" drum that matches
the tightness of the drums that so many others seem to
have, but it just hasn't happened on the 10+ axles
I've done...



Kenyon Wills

























_________________________________________________________________________
___
________
Never miss an email again!
Yahoo! Toolbar alerts you the instant new Mail arrives.
http://tools.search.yahoo.com/toolbar/features/mail/


-----------------  http://www.imperialclub.com  -----------------
This message was sent to you by the Imperial Mailing List. Please
reply to mailing-list@xxxxxxxxxxxxxxxx and your response will be
shared with everyone. Private messages (and attachments) for the
Administrators should be sent to webmaster@xxxxxxxxxxxxxxxx
To UN-SUBSCRIBE, go to http://imperialclub.com/unsubscribe.htm



-----------------  http://www.imperialclub.com  -----------------
This message was sent to you by the Imperial Mailing List. Please
reply to mailing-list@xxxxxxxxxxxxxxxx and your response will be
shared with everyone. Private messages (and attachments) for the
Administrators should be sent to webmaster@xxxxxxxxxxxxxxxx
To UN-SUBSCRIBE, go to http://imperialclub.com/unsubscribe.htm


________________________________________________________________________
AOL now offers free email to everyone. Find out more about what's free from AOL at AOL.com.


-----------------  http://www.imperialclub.com  -----------------
This message was sent to you by the Imperial Mailing List. Please reply to mailing-list@xxxxxxxxxxxxxxxx and your response will be shared with everyone. Private messages (and attachments) for the
Administrators should be sent to webmaster@xxxxxxxxxxxxxxxx
To UN-SUBSCRIBE, go to http://imperialclub.com/unsubscribe.htm



Home Back to the Home of the Forward Look Network


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.