RE: FOLLOWUP: 300C Hauls A** was: Re: [Chrysler300] Warning to Fand G
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

RE: FOLLOWUP: 300C Hauls A** was: Re: [Chrysler300] Warning to Fand G owners



Wild Bunch!  Sounds like a low budget 50's movie.

-----Original Message-----
From: Chrysler300@xxxxxxxxxxxxxxx [mailto:Chrysler300@xxxxxxxxxxxxxxx] On
Behalf Of Thomas Miller
Sent: Wednesday, September 26, 2007 8:44 PM
To: moparpjf@xxxxxxx; rob kern; chrysler300@xxxxxxxxxxxxxxx; Richard Osborne
Subject: FOLLOWUP: 300C Hauls A** was: Re: [Chrysler300] Warning to Fand G
owners

Ok,

As the other party affiliated with the (Ahhem) "sprited" driving that
started this thread, I can tell you that my 300C produced in March of '57
does indeed have a screw affixed at either end of its upper windshield
modling.  The molding itself appears to have been stamped to mate with the
pan head type screws that are currently there.  

I'll also report that nothing at all flew off of the car at 125MPH+  <grin>.
So, please would all of you F & G owners stay to the right when you see a
C, D or E closing in your rear view mirror.....   <BIGGER GRIN!>

Take care everybody.

TFM

>>> "rob kern" <robkern@xxxxxxxxxxxxx> 9/24/2007 10:50:15 PM >>>
Pete, et al,
    Very interesting info. regarding the windshield upper molding.  Recently
(at the Lawton Meet) it was pointed out to me that the upper windshield
stainless molding on my C was perhaps incorrectly mounted since the ends
were affixed wirh screws. Was this a modification made by a previous owner
during restoration without the proper clips?  Could this been from the
factory since my C was a late August '57 car and there was a shortage of
clips and this was the factory remedy to just get the car shipped to the
dealer? Or could this have been out of necessity after one flying off at any
speed? An interesting validation car was the '57 DeSoto Adventurer hardtop
seen this summer at '57 Heaven in Branson, MO.  It had an identicle screw
arrangement at the corners of the upper windshield molding that I have!  See
you in Springfield!  ROB KERN
  ----- Original Message ----- 
  From: moparpjf@xxxxxxx 
  To: richard@xxxxxxxxxxxx ; chrysler300@xxxxxxxxxxxxxxx 
  Sent: Monday, September 24, 2007 2:00 PM
  Subject: Re: [Chrysler300] Warning to F and G owners



  In a message dated 9/24/2007 2:25:56 P.M. Eastern Daylight Time, 
  richard@xxxxxxxxxxxx writes:

  When I got home, I learned that the noise was from the upper windshield 
  molding. The right side screw had popped out and the trim swung around
pivoting 
  on the left side screw. It scratched up the roof a little, but at least it

  didn't fly off. I think it can be reused.

  So, I noticed the last couple of times I washed the car that I had to push

  the trim back down, I just didn't pay attention to the true cause.
Probably 
  could have avoided another trip to the body shop if I had "listened" to
the car 
  better before this happened.

  I lost the molding twice on my K - finally realized that as your speed 
  increases, so does the vacuum built up just at the top of the windshield
(either 
  that or the wind is getting under the molding). In either event, in
addition 
  to screwing the ends down, I found that a piece of double sided tape
running 
  the length of the molding strip solves the problem once and for all.

  Pete Fitch

  ************************************** See what's new at
http://www.aol.com 

  [Non-text portions of this message have been removed]



   

[Non-text portions of this message have been removed]




To send a message to this group, send an email to:
Chrysler300@xxxxxxxxxxxxxxx

For list server instructions, go to
http://www.chrysler300club.com/yahoolist/inst.htm

For archives go to http://www.forwardlook.net/300-archive/ 
Yahoo! Groups Links







To send a message to this group, send an email to:
Chrysler300@xxxxxxxxxxxxxxx

For list server instructions, go to http://www.chrysler300club.com/yahoolist/inst.htm

For archives go to http://www.forwardlook.net/300-archive/ 
Yahoo! Groups Links

<*> To visit your group on the web, go to:
    http://groups.yahoo.com/group/Chrysler300/

<*> Your email settings:
    Individual Email | Traditional

<*> To change settings online go to:
    http://groups.yahoo.com/group/Chrysler300/join
    (Yahoo! ID required)

<*> To change settings via email:
    mailto:Chrysler300-digest@xxxxxxxxxxxxxxx 
    mailto:Chrysler300-fullfeatured@xxxxxxxxxxxxxxx

<*> To unsubscribe from this group, send an email to:
    Chrysler300-unsubscribe@xxxxxxxxxxxxxxx

<*> Your use of Yahoo! Groups is subject to:
    http://docs.yahoo.com/info/terms/
 


Home Back to the Home of the Forward Look Network Archive Sitemap


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.