Re: [Chrysler300] 300F Brakes Again!
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [Chrysler300] 300F Brakes Again!





My 300H "developed" that problem during restoration in 1985. It had the problem until 2012 when booster Dewey in Portland commented that I had the wrong vacuum booster for  the car. One of the 300 clubs lists a NAPA  p/n as a replacement and that is wrong because NAPA is wrong. It fits and half-a%% works. 
My 300H takes a dual diphragm booster and the NAPA p/n is a single diaphragm. The correct booster made a huge difference.

Mike Moore
300H   
On Aug 1, 2014, at 6:39 AM, 'John Grady' jkg@xxxxxxxxxxxxxxxxx [Chrysler300] <Chrysler300-noreply@xxxxxxxxxxxxxxx> wrote:

 

Same thing I said,  based on low pedal, way back..I think Don is right..you have a manual brake master cylinder in there ; I think they have narrower bore and longer stroke, to get same CC it moves more, but as I said in other email, brake pedal mechanical ratio is also different on parts under dash.

 

Thing must stop on a dime , with power working a manual cylinder! But more travel gives low pedal with low ratio power pedaI ; I had other problem, apparently (later dual) power master with 60 power pedal and no  booster; unbelievably hard to stop car  but pedal hardly moved. Cannot mix and match.

 

Did not know what Don adds,---- thought it was variants among suppliers, have seen both types ; I changed pedal ratio but (accidently, knowing this) kept power master, with higher ratio pedal, works ok, a little stiff. Do not have info handy, but check various bores. Looks the same outside . Apparently same thing on dual MC too .Good to know about all this

 

From: Chrysler300@xxxxxxxxxxxxxxx [mailto:Chrysler300@xxxxxxxxxxxxxxx] On Behalf Of 'Don Verity' d.verity@xxxxxxx [Chrysler300]
Sent: Thursday, July 31, 2014 8:28 PM
To: Terry Mctaggart; Listserver Chrysler Club
Subject: Re: [Chrysler300] 300F Brakes Again!

 




Hi Terry,

Wrong master cylinder. Sounds like one for a manual brake car. You can only get them out with the unit in a vise.
Don

 

Sent: Thursday, July 31, 2014 8:23 PM

Subject: [Chrysler300] 300F Brakes Again!

 

 

Terry McTaggart here in Dayton OH.  New wheel cylinders, new master cylinder, new fluid, linings are great, all done by my local shop.  And I myself jacked the car up and adjusted all the brakes.  Car stops fine, but the pedal is low.  Shop manual says the adjustment for this is the pushrod from the brake assembly thru the firewall into the master cylinder.  But my car has a one-piece push rod, so there is no adjustment.  So Murray Park sent me the correct two-piece pushrod.  Inside the car, I disconnected the current pushrod from the brake pedal, but when  I attempted to slide the pushrod out, it would not come out, even when I used considerable force.  Looking at the manual, it should just slide out.  Anybody got any ideas as to why it won't come out?








__._,_.___

Posted by: Michael Moore <mmoore8425@xxxxxxx>


To send a message to this group, send an email to:
Chrysler300@xxxxxxxxxxxxxxx

To unsubscribe from this group, send an email to bob@xxxxxxxxxxxxx or
go to http://autos.groups.yahoo.com/group/Chrysler300/join and select the "Leave Group" button

For list server instructions, go to http://www.chrysler300club.com/yahoolist/inst.htm

For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang





__,_._,___


Home Back to the Home of the Forward Look Network Archive Sitemap


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.